www.micropowerdirect.com

Model Selection Guide

Model

Number

Input

Output

Load

Regulation

(%, Max)

Efficiency

(%, Typ)

Output

Capacitive

Load

(µF, Max)

Fuse Rating

Slow-Blow

(mA)

Voltage

(VDC)

Current

(mA, Max)

Current

(mA, Min)

Nominal

Range

Full-Load No-Load

ML205S-03

5

4.50 - 5.50

471

60

3.3

500

10.0

11

73

47

1,000

ML205S-05

5

4.50 - 5.50

548

60

5.0

400

8.0

11

78

47

1,000

ML205S-12

5

4.50 - 5.50

514

60

12.0

165

3.0

11

78

10

1,000

ML205D-05

5

4.50 - 5.50

541

60

±5.0

±200

±4.0

10

74

10

1,000

ML205D-12

5

4.50 - 5.50

524

60

±12.0

±83

±1.5

7

78

4.7

1,000

ML205D-15

5

4.50 - 5.50

521

60

±15.0

±66

±1.0

7

78

4.7

1,000

ML212S-03

12

10.8 - 13.2

191

30

3.3

500

10.0

8

74

47

500

ML212S-05

12

10.8 - 13.2

222

30

5.0

400

8.0

8

76

47

500

ML212S-12

12

10.8 - 13.2

209

30

12.0

165

3.0

5

79

10

500

ML212D-12

12

10.8 - 13.2

208

30

±12.0

±83

±1.5

5

78

4.7

500

ML212D-15

12

10.8 - 13.2

206

30

±15.0

±66

±1.0

5

79

4.7

500

ML224S-03

24

21.6 - 26.4

96

15

3.3

500

10.0

8

72

47

250

ML224S-05

24

21.6 - 26.4

111

15

5.0

400

8.0

8

78

47

250

ML224S-12

24

21.6 - 26.4

105

15

12.0

165

3.0

5

77

10

250

ML224D-12

24

21.6 - 26.4

105

15

±12.0

±83

±1.5

5

78

4.7

250

ML224D-15

24

21.6 - 26.4

104

15

±15.0

±66

±1.0

5

78

4.7

250

Derating Curve

Notes:

1. The specified maximum capacitive load is for each output.

2. Load regulation is measured for an output change of 20% to 100%.

3. When measuring output ripple, it is recommended that an external 0.33 µF ceramic capacitor

be placed from each output to the common pin. For noise sensitive applications, the use of 3.3

µF capacitors will reduce the output ripple.

4. Operation at no-load will not damage these units. However, they may not meet all specifications.

5. The converter should be connected to a low ac-impedance source. An input source with a

highly inductive impedance may affect the stability of the converter. In applications where the

converter output loading is high and input power is supplied over long lines, it may be necessary

to use a capacitor on the input to insure start-up.

In this case, it is recommended that a low ESR (ESR <1.0

 at 100 kHz) capacitor be mounted

close to the converter. For 5V input units a 2.2 µF is recommended; a 1.0 µF for 12V input

units; and for 24V input models, a 0.47 µF.

6. Dual output units may be connected to provide a 10 VDC, 24 VDC or 30 VDC output. To do this,

connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output

common.

7. It is recommended that a fuse be used on the input of a power supply for protection. See the

table above for the correct rating.

Reflow Solder Settings

The ML200x series is designed to meet the IPC/

JEDEC standard J-STD-020D for reflow solder-

ing. The recommended reflow settings are a peak

temperature of 245 °C for a maximum period

(TPK) of 10S and a time above liquidous (TL) of

<60 seconds at 217 °C, as illustrated above. For

more information, please contact the factory.