Electronic Components Datasheet Search
  English  ▼

X  

LTM4675 Datasheet(PDF) 6 Page - Linear Technology

Part # LTM4675
Description  PolyPhase Step-Down Slave Controller for Digital Power System Management
PDF  20 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  LINER [Linear Technology]
Direct Link  http://www.linear.com
Logo LINER - Linear Technology

LTM4675 Datasheet(HTML) 6 Page - Linear Technology

Back Button LTM4675 Datasheet HTML 2Page - Linear Technology LTM4675 Datasheet HTML 3Page - Linear Technology LTM4675 Datasheet HTML 4Page - Linear Technology LTM4675 Datasheet HTML 5Page - Linear Technology LTM4675 Datasheet HTML 6Page - Linear Technology LTM4675 Datasheet HTML 7Page - Linear Technology LTM4675 Datasheet HTML 8Page - Linear Technology LTM4675 Datasheet HTML 9Page - Linear Technology LTM4675 Datasheet HTML 10Page - Linear Technology Next Button
Zoom Inzoom in Zoom Outzoom out
 6 / 20 page
background image
LTC3870-1
6
38701f
For more information www.linear.com/LTC3870-1
ISENSE0+/ISENSE1+(Pin1/Pin6):CurrentSenseComparator
positive inputs, normally connected to the positive node
of the DCR sensing networks or current sensing resistors.
ISENSE0−/ISENSE1−(Pin2/Pin5):CurrentSenseComparator
negative inputs, normally connected to the negative node
of the DCR sensing network or current sensing resistors.
RUN0/RUN1 (Pin 3/Pin 4): Enable Run Input Pins. A logic
high on these pins enables the corresponding channel.
In multiphase operation, these pins are connected to
LTC3887-1's RUN pins.
MODE0/MODE1 (Pin 24/Pin 7): DCM/CCM Mode Control
Pins. Channel0/Channel1 operate in forced continuous
mode if MODE0/MODE1 pin is logic high. There is a 500kΩ
pull-down resistor on MODE0/MODE1 internally. The
default operation mode in each channel is discontinuous
mode operation unless these pins are actively driven high.
ITH0/ITH1 (Pin 23/Pin 8): Current Control Threshold.
Each associated channel’s current comparator tripping
threshold increases with its ITH voltage. In multiphase
operation, these pins are connected to the master con-
troller's ITH pins for current sharing.
ILIM (Pin 9): Programs Current Comparators' Sense
Voltage Range. This pin can be tied to GND or INTVCC
to select the maximum current sense threshold for each
current comparator. GND sets both channels' current low
range with maximum 50mV sensing voltage. INTVCC sets
both channels' current high range with maximum 75mV
sensing voltage. For equal current sharing, the setup on
the ILIM pin has to be same as the setup on the bit 7 of
MFR_PWM_MODE_3887-1registerinthemastercontrol-
ler. See Table 2 in the Operation Section for details.
SYNC (Pin 10): External Clock Synchronization Input. If an
externalclockispresentatthispin,theswitchingfrequency
will be synchronized to the falling edge of the external
clock. In multiphase operation, this pin is connected to
LTC3887-1 SYNC pin for frequency synchronization. Do
not float the SYNC Pin.
PHASMD (Pin 11): Phase Set Pin. This pin can be tied to
GND,INTVCCoraresistordividerfromINTVCCtoGND.This
pin determines the relative phases between the external
clock on the SYNC pin and the internal controllers. See
Table 1 in the Operation Section for details.
PWM0/PWM1 (Pin 19/Pin 12): (Top) Gate Signal Outputs.
ThissignalgoestothePWMortopgateinputoftheexternal
driver, integrated driver MOSFET or Power Block. This is
a three-state compatible output. To support three-state
mode, an external resistive divider is typically used from
VCC0/VCC1 to ground.
VCC0/VCC1 (Pin 18/Pin 13): PWM Pin Driver Supplies.
Decouple these pins to GND with a capacitor (0.1µF) or tie
these pins to the INTVCC pin. PWM0/PWM1 signal swing
is from ground to VCC0/VCC1.
INTVCC(Pin14):InternalRegulator5VOutput.Theinternal
control circuits are powered from this voltage. Bypass this
pin to GND with a minimum of 4.7µF low ESR tantalum
or ceramic capacitor. INTVCC is enabled as soon as VIN
is powered. The INTVCC pin is not short circuit proof. If
overloaded, this will disrupt internal operation that can
damage the part.
EXTVCC (Pin 15): External power input to an internal LDO
connected to INTVCC. This LDO supplies INTVCC power
bypassing the internal LDO powered from VIN whenever
EXTVCC is higher than 4.8V. See EXTVCC connection in the
Applications Information Section. Do not exceed 14V on
this pin. Bypass this pin to GND with a minimum of 4.7µF
low ESR tantalum or ceramic capacitor. If the EXTVCC pin
is not used, leave it open or tie it to ground. EXTVCC can
be present before VIN. However, EXTVCC is enabled only
if VIN is higher than 6.5V.
GND (Pin 16/Exposed Pad Pin 25): Signal ground. All
small-signal and compensation components should con-
nect to this ground. The exposed pad must be soldered
pin FuncTions



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com