| Electronic Components Datasheet Search |
|
LTM4675 Datasheet(PDF) 9 Page - Linear Technology |
|
|
|||||||||||||||||||||||||||||
LTM4675 Datasheet(HTML) 9 Page - Linear Technology |
|
9 / 20 page ![]() LTC3870-1 9 38701f For more information www.linear.com/LTC3870-1 GND, the LTC3870-1 operates in discontinuous mode at light loads. At very light loads, the current comparator ICMP may remain tripped for several cycles and force the external top MOSFET to stay off for the same number of cycles (i.e., skipping pulses). This mode provides higher light load efficiency than forced continuous mode and the inductor current is not allowed to reverse. There are 500kΩ pull-down resistors internally connected to the MODE0/MODE1 pins. If MODE0/MODE1 pins are floating, bothchannelsdefaulttoDiscontinuousConductionMode. Multichip Operation (PHASMD and SYNC Pins) The PHASMD pin determines the relative phases between the internal channels as well as the external clock signal on the SYNC pin, as shown in Table 1. The phases tabulated are relative to zero degree phase being defined as the falling edge of the clock on SYNC. Table 1. PHASMD Channel 0 Phase Channel 1 Phase GND 180° 0° 1/3 INTVCC 60° 300° 2/3 INTVCC or Float 120° 240° INTVCC 90° 270° The SYNC pin is used to synchronize switching frequency between master and slave controllers. Input capacitance ESR requirements and efficiency losses are substantially reduced because the peak current drawn from the input capacitor is effectively divided by the number of phases used and power loss is proportional to the RMS current squared. A two-phase, single output voltage implementa- tion can reduce input path power loss by 75% and radi- cally reduce the required RMS current rating of the input capacitor(s). operaTion Single Output Multiphase Operation TheLTC3870-1isdesignedformultiphaseconverterswith the LTC3887-1 by making these connections: • Tie all the ITH pins of paralleled channels together for current sharing between masters and slaves. Note that ILIM setup on slaves has to match MFR_PWM_MODE current range setup in masters. • Tie all SYNC pins together between master and slaves for same switching frequency synchronization; one and only one of the LTC3887-1 controllers has to be programmed as master to generate clock signal on the SYNC pin. • Tie all the RUN pins of paralleled channels together between master and slaves for startup and shutdown sequences. • Tie the GPIO pin of the master controller to the FAULT pin of slave controller and program the master GPIO as fault sharing for fault protection. Examples of single output multiphase converters are shown in Figure 1. Inductor Current Sensing Like the LTC3887-1, the LTC3870-1 can use either induc- tor DCR or RSENSE to sense the inductor current. Inductor DCR current sensing provides a lossless method of sens- ing the instantaneous current. Therefore, it can provide higherefficiencyforapplicationswithhighoutputcurrents. However, the DCR of a copper inductor typically has 10% tolerance.Forprecisecurrentsensing,aprecisionsensing resistor RSENSE can be used to sense the inductor current. Itisimportanttomatchthecurrentsensingcircuitbetween master controllers and slave controllers to guarantee bal- anced load sharing and overcurrent protection. |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |