LT3437 datasheet(3/24 Pages) LINER

3 / 24 page

LT3437

3437f

Note 1: Absolute Maximum Ratings are those values beyond which the life of

a device may be impaired.

Note 2: The LT3437EDD/LT3437EFE are guaranteed to meet performance

specifications from 0

°C to 125°C junction temperature. Specifications over

the –40

°C to 125°C operating junction temperature range are assured by

design, characterization and correlation with statistical process controls. The

LT3437IDD/LT3437IFE are guaranteed and tested over the full –40

°C to

125

°C operating junction temperature range.

Note 3: Minimum input voltage is defined as the voltage where switching

starts. Actual minimum input voltage to maintain a regulated output will

depend upon output voltage and load current. See Applications Information.

Note 4: Supply input current is the quiescent current drawn by the input

pin. Its typical value depends on the voltage on the BIAS pin and operating

state of the LT3437. With the BIAS pin at 0V, all of the quiescent current

required to operate the LT3437 will be provided by the VIN pin. With the

BIAS voltage above its minimum input voltage, a portion of the total

quiescent current will be supplied by the BIAS pin. Supply sleep current is

defined as the quiescent current during the “sleep” portion of Burst Mode

operation. See Applications Information for determining application supply

currents.

Note 5: Minimum BIAS voltage is the voltage on the BIAS pin when IBIAS is

sourced into the pin.

Note 6: This is the minimum voltage across the boost capacitor needed to

guarantee full saturation of the internal power switch.

Note 7: Boost current is the current flowing into the BOOST pin with the pin

held 3.3V above input voltage. It flows only during switch on time.

Note 8: Gain is measured with a VC swing from 1.15V to 750mV.

Note 9: Switch saturation voltage guaranteed by correlation to wafer level

measurements for DD package parts.

Note 10: The CSS threshold is defined as the value of current sourced into the

CSS pin which results in an increase in sink current from the VC pin. See the

Soft-Start section in Applications Information.

SYMBOL

PARAMETER

CONDITIONS

MIN

TYP

MAX

UNITS

IBIASS

BIAS Sleep Current (Note 4)

●

150

250

µA

IBIAS

BIAS Quiescent Current

SYNC = 2V

0.75

Minimum Boost Voltage (Note 6)

ISW = 250mA

1.8

2.5

Input Boost Current (Note 7)

ISW = 0.5A

ISW = 0.25A

VREF

Reference Voltage (VREF)

3.3V < VVIN < 80V

● 1.225

1.25

1.275

IFB

FB Input Bias Current

200

EA Voltage Gain (Note 8)

900

V/V

EA Voltage gm

dI(VC)= ±10µA

650

µMho

EA Source Current

FB = 1.15V

µA

EA Sink Current

FB = 1.35V

µA

VC to SW gm

1A/V

VC Switching Threshold

VSYNC = 2V

500

VC High Clamp

1.5

1.75

2.1

IPK

SW Current Limit

●

500

650

900

SW VCESAT

Switch Saturation Voltage

ISW = 250mA

●

200

400

(Note 9)

ISW = 500mA

●

400

800

Switching Frequency

●

170

200

240

kHz

Maximum Duty Cycle

Minimum SYNC Amplitude

1.5

SYNC Frequency Range

240

700

kHz

SYNC Input Impedance

Ω

ICSS

CSS Current Threshold (Note 10)

FB = 0V

µA

The

● denotes the specifications which apply over the full operating

temperature range, otherwise specifications are at TJ = 25°C. VIN = 12V, SHDN = 12V, BIAS = 5V, FB = 1.25V,

CSS/SYNC = 0V unless otherwise noted.

ELECTRICAL CHARACTERISTICS

LT3437 Datasheet(PDF) 3 Page - Linear Technology

LT3437 Datasheet(HTML) 3 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Datasheet Download

Link URL