| Electronic Components Datasheet Search |
|
VSC7938 Datasheet(PDF) 8 Page - Vitesse Semiconductor Corporation |
|
|
|||||||||||||||||||||||||||||
VSC7938 Datasheet(HTML) 8 Page - Vitesse Semiconductor Corporation |
|
8 / 16 page ![]() VITESSE SEMICONDUCTOR CORPORATION Preliminary Data Sheet VSC7938 SONET/SDH 3.125Gb/s Laser Diode Driver with Automatic Power Control Page 8 G52349-0, Rev 3.0 01/20/01 © VITESSE SEMICONDUCTOR CORPORATION • 741 Calle Plano • Camarillo, CA 93012 Tel: (800) VITESSE • FAX: (805) 987-5896 • Email: prodinfo@vitesse.com Internet: www.vitesse.com Detailed Description The VSC7938 is a high-speed laser driver with Automatic Power Control. The device is designed to operate up to 3.125Gb/s with a 3.3V or 5V supply. The data and clock inputs support PECL inputs as well as other inputs that meet the common-mode voltage and differential voltage swing specifications. The differential pair output stage is capable of sinking up to 60mA from the laser with typical rise and fall times of 60ps. This output may be DC-coupled for 5V operation. To allow for larger output swings during 3.3V operation, the VSC7938 was designed to be AC-coupled to the laser cathode with a pull-up inductor for DC-biasing. This configuration will isolate laser forward voltage from the output circuitry and will allow the output at OUT+ to swing above and below the supply voltage VCC. The key features of the VSC7938 are Automatic Power Control, low power supply current, and fast rise and fall times. The VSC7939 and VSC7940 are other Vitesse laser drivers with similar features in a 32-pin TQFP package. These devices also have pins for monitoring modulation and bias currents. The VSC7940 is a special version of the VSC7939 designed to drive 100mA into a DC-coupled load with a 5V supply. Automatic Power Control To ensure constant average optical power, the device utilizes an Automatic Power Control loop. A photo- diode mounted in the laser package provides optical feedback to compensate for changes in average laser output power due to changes that affect laser performance such as temperature and laser lifetime. The laser bias current is adjusted by the APC loop according to the reference current set at APCSET by an external resistor. An exter- nal capacitor at CAPC controls the time constant for the APC feedback loop. The recommended value for CAPC is 0.1 µF. This value reduces pattern-dependent jitter associated with the APC feedback loop and guaran- tees stability. Because the APC loop noise is internally filtered, APCFILT is not internally connected and does not need to be connected to any external components. The device’s performance will not be affected if a capac- itor is connected to APCFILT. If the APC loop cannot adjust the bias current to track the desired monitor cur- rent, FAIL is set low. The device may be operated with or without APC. To utilize APC, a capacitor must be connected at CAPC (0.1 µF) and a resistor must be connected at APCSET to set the average optical power. For open-loop operation (no APC), a 100k Ω resistor should be connected between APCSET and GND. CAPC has no effect on open- loop operation. In both modes of operation, resistors to ground should be placed at BIASMAX and MODSET to set the bias and modulation currents. Data Retiming The VSC7938 provides inputs for differential PECL clock signals for data retiming to minimize jitter at high speeds. To incorporate this function, LATCH should be connected to VCC. If this function is unused, CLK+ should be connected to VCC, CLK- should be left unconnected, and LATCH should be connected to GND. Short-Circuit Protection If BIASMAX or MODSET are shorted to ground, the output modulation and bias currents will be turned off. |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |