Electronic Components Datasheet Search
  English  ▼

X  

PM39F040 Datasheet(PDF) 7 Page - PMC-Sierra, Inc

Part # PM39F040
Description  1 Mbit / 2 Mbit / 4 Mbit 5 Volt-only CMOS Flash Memory
PDF  23 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  PMC [PMC-Sierra, Inc]
Direct Link  http://www.pmc-sierra.com
Logo PMC - PMC-Sierra, Inc

PM39F040 Datasheet(HTML) 7 Page - PMC-Sierra, Inc

Back Button PM39F040 Datasheet HTML 3Page - PMC-Sierra, Inc PM39F040 Datasheet HTML 4Page - PMC-Sierra, Inc PM39F040 Datasheet HTML 5Page - PMC-Sierra, Inc PM39F040 Datasheet HTML 6Page - PMC-Sierra, Inc PM39F040 Datasheet HTML 7Page - PMC-Sierra, Inc PM39F040 Datasheet HTML 8Page - PMC-Sierra, Inc PM39F040 Datasheet HTML 9Page - PMC-Sierra, Inc PM39F040 Datasheet HTML 10Page - PMC-Sierra, Inc PM39F040 Datasheet HTML 11Page - PMC-Sierra, Inc Next Button
Zoom Inzoom in Zoom Outzoom out
 7 / 23 page
background image
Programmable Microelectronics Corp.
Issue Date: March, 2004, Rev: 1.3
PMC
Pm39F010 / Pm39F020 / Pm39F040
7
BLOCK DIAGRAM
DEVICE OPERATION
READ OPERATION
The access of Pm39F010/020/040 are similar to
EPROM. To read data, three control functions must be
satisfied:
• CE# is the chip enable and should be pulled low
( VIL ).
• OE# is the output enable and should be pulled
low ( VIL).
• WE# is the write enable and should remains high
( VIH ).
PRODUCT IDENTIFICATION
The product identification mode can be used to identify
the manufacturer and the device through hardware or
software read ID operation. See Table 1 for PMC Manu-
facturer ID and Device ID. The hardware ID mode is acti-
vated by applying a 12.0 Volt on A9 pin, typically used
by an external programmer for selecting the right pro-
gramming algorithm for the devices. Refer to Table 2 for
Bus Operation Modes. The software ID mode is acti-
vated by a three-bus-cycle command. See Table 3 for
Software Command Definition.
WE#
CE#
OE#
COMMAND
REGISTER
CE,OE LOGIC
A0-A
MS
ERASE/PROGRAM
VOLTAGE
GENERATOR
HIGH VOLTAGE
SWITCH
I/O0-I/O7
I/O BUFFERS
DATA
LATCH
SENSE
AMP
Y-GATING
MEMORY
ARRAY
Y-DECODER
X-DECODER
BYTE PROGRAMMING
The programming is a four-bus-cycle operation and the
data is programmed into the devices (to a logical “0”) on
a byte-by-byte basis. See Table 3 for Software Com-
mand Definition. A program operation is activated by writ-
ing the three-byte command sequence followed by pro-
gram address and one byte of program data into the
devices. The addresses are latched on the falling edge
of WE# or CE# whichever occurs later, and the data are
latched on the rising edge of WE# or CE# whichever
occurs first. The internal control logic automatically
handles the internal programming voltages and timing.
A data “0” can not be programmed back to a “1”. Only
erase operation can convert the “0”s to “1”s. The Data#
Polling on I/O7 or Toggle Bit on I/O6 can be used to
detect the progress or completion of a program cycle.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com