ADGS1612 datasheet(23/29 Pages) AD

23 / 29 page

Data Sheet

ADGS1612

Rev. 0 | Page 23 of 29

SCLK Count Error Detection

SCLK count error detection allows the user to detect if an incorrect

number of SCLK cycles are sent by the microcontroller or CPU.

When in address mode, with CRC disabled, 16 SCLK cycles are

expected. If 16 SCLK cycles are not detected, the SCLK count

error flag asserts in the error flags register. When less than

16 SCLK cycles are received by the device, a write to the register

map never occurs. When the ADGS1612 receives more than

16 SCLK cycles, a write to the memory map still occurs at the

16th SCLK rising edge, and the flag asserts in the error flags

cycles is 24. SCLK count error detection is enabled by default

and can be configured by the user through the error

configuration register.

Invalid Read/Write Address Error

An invalid read/write address error detects when a nonexistent

error asserts when a write to a read only register is attempted.

The invalid read/write address error flag asserts in the error

flags register when an invalid read/write address error occurs.

The invalid read/write address error is detected on the ninth

SCLK rising edge, which means a write to the register never

occurs when an invalid address is targeted. Invalid read/write

address error detection is enabled by default and can be

disabled by the user through the error configuration register.

CLEARING THE ERROR FLAGS REGISTER

To clear the error flags register, write the special 16-bit SPI

frame, 0x6CA9, to the device. This SPI command does not

trigger the invalid R/W address error. When CRC is enabled,

the user must also send the correct CRC byte to complete an

error clear command. At the 16th or 24th SCLK rising edge, the

error flags register resets to zero.

BURST MODE

The SPI interface can accept consecutive SPI commands

without the need to deassert the CS line, which is called burst

mode. Burst mode is enabled through the burst enable register.

This mode uses the same 16-bit command to communicate

with the device. In addition, the response of the device at SDO

is still aligned with the corresponding SPI command. Figure 41

shows an example of SDI and SDO during burst mode.

The invalid read/write address and CRC error checking functions

operate similarly during burst mode as they do during address

mode. However, SCLK count error detection operates in a

slightly different manner. The total number of SCLK cycles

within a given CS frame are counted, and if the total is not a

multiple of 16 or a multiple of 24 when CRC is enabled, the

SCLK count error flag asserts.

SDO

COMMAND 0[15:0]

RESPONSE 0[15:0]

COMMAND 1[15:0]

RESPONSE 1[15:0]

COMMAND 2[15:0]

RESPONSE 2[15:0]

COMMAND 3[15:0]

RESPONSE 3[15:0]

SDI

Figure 41. Burst Mode Frame

SOFTWARE RESET

When in address mode, the user can initiate a software reset. To

do so, write two consecutive SPI commands, namely 0xA3 fol-

lowed by 0x05, targeting Register 0x0B. After a software reset,

all register values are set to default.

DAISY-CHAIN MODE

The connection of several ADGS1612 devices in a daisy-chain

configuration is possible, and Figure 42 shows this setup. All

devices share the same CS and SCLK line, whereas the SDO pin of

a device forms a connection to the SDI pin of the next device,

creating a shift register. In daisy-chain mode, SDO is an eight-cycle

delayed version of SDI. When in daisy-chain mode, all commands

target the switch data register. Therefore, it is not possible to

make configuration changes while in daisy-chain mode.

SDI

SCLK

RESET/VL

SDO

ADGS1612

DEVICE 1

RESET/VL S4

SDO

ADGS1612

DEVICE 2

SPI

INTERFACE

SPI

INTERFACE

Figure 42. Two SPI Controlled Switches Connected in a Daisy-Chain Configuration

ADGS1612 Datasheet(PDF) 23 Page - Analog Devices

ADGS1612 Datasheet(HTML) 23 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29

Datasheet Download

Link URL