HT49CV7 datasheet(18/48 Pages) HOLTEK

18 / 48 page

HT49RV7/HT49CV7

Rev. 1.00

April 20, 2006

Timer/Event Counter

Two timer/event counters (TMR0,TMR1) are imple-

mented in the microcontroller. The Timer/Event Counter

0 contains a 16-bit programmable count-up counter and

the clock may come from an external source or an inter-

nal clock source. An internal clock source comes from

fSYS. The Timer/Event Counter 1 contains a 16-bit pro-

grammable count-up counter and the clock may come

from an external source or an internal clock source. An

internal clock source comes from fSYS/4 or 32768Hz se-

lected by option. The external clock input allows the

user to count external events, measure time intervals or

pulse widths, or to generate an accurate time base.

There are six registers related to the Timer/Event Coun-

ter 0; TMR0H (0CH), TMR0L (0DH), TMR0C (0EH) and

the Timer/Event Counter 1, TMR1H (0FH), TMR1L

(10H), and TMR1C (11H). Writing TMR0L (TMR1L) will

only place the written data to an internal lower-order

byte buffer (8-bit) and writing TMR0H (TMR1H) will

transfer the specified data and the contents of the

lower-order byte buffer to TMR0H (TMR1H) and TMR0L

(TMR1L) registers, respectively. The Timer/Event

Counter 1/0 preload register is changed by each writing

TMR0H (TMR1H) operations. Reading TMR0H

(TMR1H) will latch the contents of TMR0H (TMR1H)

and TMR0L (TMR1L) counters to the destination and

the lower-order byte buffer, respectively. Reading the

TMR0L (TMR1L) will read the contents of the

lower-order byte buffer. The TMR0C (TMR1C) is the

Timer/Event Counter 0 (1) control register, which de-

fines the operating mode, counting enable or disable

and an active edge.

The TM0 and TM1 bits define the operation mode. The

event count mode is used to count external events,

which means that the clock source is from an external

(TMR0, TMR1) pin. The timer mode functions as a nor-

mal timer with the clock source coming from the internal

selected clock source. Finally, the pulse width measure-

ment mode can be used to count the high or low level

duration of the external signal (TMR0, TMR1), and the

counting is based on the internal selected clock source.

In the event count or timer mode, the timer/event coun-

ter starts counting at the current contents in the

timer/event counter and ends at FFFFH. Once an over-

flow occurs, the counter is reloaded from the timer/event

counter preload register, and generates an interrupt re-

quest flag (T0F; bit 6 of INTC0, T1F; bit 4 of INTC1). In

the pulse width measurement mode with the values of

the TON and TE bits equal to 1, after the TMR0 (TMR1)

has received a transient from low to high (or high to low if

R e l o a d

O v e r f l o w

t o I n t e r r u p t

P F D 0

P A 3 D a t a C T R L

T 0 M 1

T 0 M 0

T M R 0

T 0 E

T 0 M 1

T 0 M 0

T 0 O N

P u l s e W i d t h

M e a s u r e m e n t

M o d e C o n t r o l

1 6 - b i t T i m e r / E v e n t C o u n t e r

P r e l o a d R e g i s t e r

1 6 - b i t T i m e r / E v e n t C o u n t e r

( T M R 0 H / T M R 0 L )

D a t a B u s

8 - s t a g e P r e s c a l e r

8 - 1 M U X

f S Y S

f I N T

T 0 P S C 2 ~ T 0 P S C 0

( 6 + 2 ) o r ( 7 + 1 )

C o m p a r e

P W M

T o P D 0 / P D 1 / P D 2 / P D 3 c i r c u i t

Timer/Event Counter 0

R e l o a d

O v e r f l o w

t o I n t e r r u p t

P F D 1

P A 3 D a t a C T R L

T 1 M 1

T 1 M 0

T M R 1

T 1 E

T 1 M 1

T 1 M 0

T 1 O N

P u l s e W i d t h

M e a s u r e m e n t

M o d e C o n t r o l

1 6 - b i t T i m e r / E v e n t C o u n t e r

P r e l o a d R e g i s t e r

1 6 - b i t T i m e r / E v e n t C o u n t e r

( T M R 1 H / T M R 1 L )

D a t a B u s

f I N T

f S Y S / 4

3 2 7 6 8 H z

T 1 S

Timer/Event Counter 1

HT49CV7 Datasheet(PDF) 18 Page - Holtek Semiconductor Inc

HT49CV7 Datasheet(HTML) 18 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

Datasheet Download

Link URL