LM4901MM datasheet(4/24 Pages) NSC

4 / 24 page

Electrical Characteristics V

DD =3V (Notes 1, 2)

The following specifications apply for the circuit shown in Figure 1, unless otherwise specified. Limits apply for T

A =

25˚C. (Continued)

Symbol

Parameter

Conditions

LM4901

Units

(Limits)

Typical

Limit

(Note 6)

(Notes 7, 9)

OUT

Resistor Output to GND (Note 10)

8.5

9.7

Ω (max)

7.0

Ω (min)

Output Power (8

Ω)

THD = 1% (max);f=1kHz

390

Ω)

THD = 1% (max);f=1kHz

525

Wake-up time

mS (max)

THD+N

Total Harmonic Distortion+Noise

o = 0.25 Wrms; f = 1kHz

0.1

PSRR

Power Supply Rejection Ratio

ripple = 200mV sine p-p

Input terminated with 10

Ω

62 (f =

217Hz)

68 (f = 1kHz)

dB (min)

Electrical Characteristics V

DD = 2.6V

(Notes 1, 2)

The following specifications apply for the circuit shown in Figure 1, unless otherwise specified. Limits apply for T

A = 25˚C.

Symbol

Parameter

Conditions

LM4901

Units

(Limits)

Typical

Limit

(Note 6)

(Notes 7, 9)

Quiescent Power Supply Current

IN = 0V, Io = 0A, No Load

2.0

mA (max)

IN = 0V, Io = 0A, 8

Ω Load

3.0

mA (max)

Shutdown Current

SD =VSD Mode (Note 8)

0.1

µA (max)

SDIH

Shutdown Voltage Input High

SD MODE =VDD

1.0

V (min)

SDIL

Shutdown Voltage Input Low

SD MODE =VDD

0.9

V (max)

SDIH

Shutdown Voltage Input High

SD MODE = GND

1.2

V (min)

SDIL

Shutdown Voltage Input Low

SD MODE = GND

1.0

V (max)

Output Offset Voltage

mV (max)

OUT

Resistor Output to GND (Note 10)

8.5

9.7

Ω (max)

7.0

Ω (min)

Output Power ( 8

Ω )

THD = 1% (max);f=1kHz

275

Ω )

THD = 1% (max);f=1kHz

340

Wake-up time

mS (max)

THD+N

Total Harmonic Distortion+Noise

o = 0.15 Wrms; f = 1kHz

0.1

PSRR

Power Supply Rejection Ratio

ripple = 200mV sine p-p

Input terminated with 10

Ω

51 (f =

217Hz)

51 (f = 1kHz)

dB (min)

Note 1: All voltages are measured with respect to the ground pin, unless otherwise specified.

Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is

functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which

guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit

is given, however, the typical value is a good indication of device performance.

Note 3: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, θJA, and the ambient temperature TA. The maximum

allowable power dissipation is PDMAX =(TJMAX–TA)/θJA or the number given in Absolute Maximum Ratings, whichever is lower. For the LM4901, see power derating

curves for additional information.

Note 4: Human body model, 100 pF discharged through a 1.5 k

Ω resistor.

Note 5: Machine Model, 220 pF–240 pF discharged through all pins.

Note 6: Typicals are measured at 25˚C and represent the parametric norm.

Note 7: Limits are guaranteed to National’s AOQL (Average Outgoing Quality Level).

Note 8: For micro SMD only, shutdown current is measured in a Normal Room Environment. Exposure to direct sunlight will increase ISD by a maximum of 2µA.

Note 9: Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis.

Note 10: RROUT is measured from the output pin to ground. This value represents the parallel combination of the 10kΩ output resistors and the two 20kΩ resistors.

Note 11: If the product is in Shutdown mode and VDD exceeds 6V (to a max of 8V VDD), then most of the excess current will flow through the ESD protection circuits.

If the source impedance limits the current to a max of 10mA, then the device will be protected. If the device is enabled when VDD is greater than 5.5V and less than

6.5V, no damage will occur, although operation life will be reduced. Operation above 6.5V with no current limit will result in permanent damage.

LM4901MM Datasheet(PDF) 4 Page - National Semiconductor (TI)

LM4901MM Datasheet(HTML) 4 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Datasheet Download

Link URL