LS-T3 datasheet(30/64 Pages) IDEC

30 / 64 page

Instructions

About PC Board and Circuit Design

1. Use PC boards made of glass epoxy copper-clad lami-

nated sheets of 1.6 mm in thickness, with double-sided

through hole.

2. PC boards and circuits must withstand rated voltage and

current, including the instantaneous current and voltage

at switching.

3. The minimum applicable load is 5V AC/DC, 1 mA. This

value may vary according to the operating environment

and load.

4. Within the 2.8

∗ mm areas shown in the figure below,

terminals touch the PC board, resulting in possible short

circuit on the printed circuit. When designing a PC board

pattern, take this possibility into consideration.

19.8

8.7

(0.5)

5.7

1.6 (PC Board)

(0.5)

2.8∗

10-ø1.2

holes

Solder

Surface

Solder Surface

Surface for installing

components

Surface for installing

components

Screw Terminal

Applicable Crimping Terminals

Solid Wire

Wire

Insulating Tube

Crimping Terminal

4.7 to 5.9

3.0 max.

ø3.2 min.

Wire

Insulating Tube

Crimping

Terminal

4.7 to 5.9

4.7 min.

6.2 max.

Ring Terminal

Spade Terminal

1. Wire thickness: 0.75 to 1.25 mm2 (AWG18 to 16)

• Be sure to install an insulating tube on the crimping terminal.

2. Tighten the M3 terminal screw to a tightening torque of

0.6 to 1.0 N·m.

Connector

1. Connector shape

• Tyco Electronics, D-2000 series

Part No. 1376009-1 (tab header, board mount)

2. Applicable connectors (to be supplied by user)

• Tyco Electronics, D-2000 series

Part No. 1-1318119-4 (receptacle housing)

• Tyco Electronics, D-2000 series

Part No. 1318107-1 (receptacle contact)

3. To prepare correct receptacles for the connector, read

the instruction sheet and catalog of Tyco Electronics and

understand the installation and wiring method.

4. Fasten the cable so that the connector is not pulled.

Otherwise the switch may be deformed and damaged,

causing malfunction or operation failure.

Installing & Removing Terminal Covers

XA9Z-VL2

To install the terminal cover, align the TOP marking on the

terminal cover with TOP marking on the contact block, and

press the terminal cover toward the contact block.

Note: For wiring, insert the wires into the holes in the terminal cover before

soldering.

XW9Z-VL2M

To install the terminal cover, align the TOP marking on the

terminal cover with the TOP marking on the contact block.

Place the two projections on the bottom side of the contact

block into the slots in the terminal cover. Press the terminal

cover toward the contact block.

TOP Marking

➀ Place the projections

on the contact bock.

➁ Press the

terminal cover

To remove the terminal cover, pull out the two latches on

the top side of the terminal cover. Do not exert excessive

force to the latches, otherwise the latches may break.

TOP Markings

Pull out the latches.

IP20 Protection Terminal Cover

XW9Z-VL2MF

To install the IP20 protection cover, align the TOP marking

on the cover with the TOP marking on the contact block,

and press the cover toward the contact block.

TOP Marking

(Press)

Notes:

1. Once installed, the XW9Z-VL2MF cannot be removed.

2. The XW9Z-VL2MF cannot be installed after wiring.

3. With the XW9Z-VL2MF installed, crimping terminals cannot be

used. Use solid wires.

4. Make sure that the XW9Z-VL2MF is securely installed. IP20 cannot

be achieved when installed loosely, and electric shocks may occur.

ø22 XW Series Emergency Stop Switches

Only solid wires

can be used

for IP20 units.

LS-T3 Datasheet(PDF) 30 Page - IDEC Corporation

LS-T3 Datasheet(HTML) 30 Page - IDEC Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

Datasheet Download

Link URL