FXPS7115D4 datasheet(41/72 Pages) NXP

41 / 72 page

NXP Semiconductors

FXPS7115D4

Digital absolute pressure sensor, 40 kPa to 115 kPa

There are 4 DSP Configuration registers which are DSP_CFG_U1, DSP_CFG_U3, DSP_CFG_U4, and

DSP_CFG_U5.

7.7.11.1 Self-test control bits

The self-test control bits of the DSP user configuration register (DSP_CFG_U5, address 44h) select one of the

various analog and digital self-test features of the device as shown in Table 73. The self-test control bits are not

included in the read/write array error detection.

7.7.11.2 DSP_CFG_U1 - DSP user configuration #1 register (address 40h)

The DSP user configuration register #1 is a user programmable read/write register that contains DSP-specific

configuration information. This register is included in the read/write array error detection.

Changes to this register reset the DSP data path. The contents of the SNSDATA_x registers are not guaranteed

until the DSP has completed initialization as specified in Table 105. Reads of the SNSDATA_x registers and

sensor data requests should be prevented during this time.

Bit

Symbol

LPF[3:0]

reserved

Factory default

Access

R/W

Table 64. DSP_CFG_U1 - DSP user configuration #1 register (address 40h) bit allocation

LPF[3]

LPF[2]

LPF[1]

LPF[0]

Low Pass Filter Type

800 Hz, 4-Pole

1000 Hz, 4-Pole[1][2]

Table 65. Low-pass filter selection bits (LPF[3:0])

[1]

Default is 1000 Hz.

[2]

In case of POR, filter reverts to the default.

Note: Using values other than those listed in Table 65 causes an error in the DEVSTAT.

7.7.11.3 DSP_CFG_U3 - DSP user configuration #3 register (address 42h)

The DSP user configuration register #3 is a user programmable read/write register that contains DSP-specific

configuration information. This register is included in the read/write array error detection.

Changes to this register reset the DSP data path. The content of the SNSDATA_x registers are not guaranteed

until the DSP has completed initialization. Reads of the SNSDATA_x registers and sensor data requests should

be prevented during this time.

This register is readable and writeable in SPI mode, and I2C mode.

Bit

Symbol

reserved

DATATYPE0[1:0]

reserved

DATATYPE1[1:0]

reserved

Reset

Access

R/W

Table 66. DSP_CFG_U3 - DSP user configuration #3 register (address 42h) bit allocation

FXPS7115D4

All information provided in this document is subject to legal disclaimers.

Product data sheet

Rev. 6.1 — 7 June 2023

41 / 72

FXPS7115D4 Datasheet(PDF) 41 Page - NXP Semiconductors

FXPS7115D4 Datasheet(HTML) 41 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72

Datasheet Download

Link URL