CLC031 datasheet(22/31 Pages) NSC

22 / 31 page

Device Operation (Continued)

TABLE 4. Video Raster Format Parameters

Format

Code

[4,3,2,1,0]

Format

Spec.

Frame

Rate

Lines

Active Lines

Samples

Active

Samples

00001

SDTV, 54

RP 174

60I

525

507/487*

3432

2880

00010

SDTV, 36

SMPTE 267

60I

525

507/487*

2288

1920

00011

SDTV, 27

SMPTE 125

60I

525

507/487*

1716

1440

01001

SDTV, 54

ITU-R BT 601.5

50I

625

577

3456

2880

01010

SDTV, 36

ITU-R BT 601.5

50I

625

577

2304

1920

01011

SDTV, 27

ITU-R BT 601.5

50I

625

577

1728

1440

10001

HDTV, 74.25

SMPTE 260

30I

1125

1035

2200

1920

10010

HDTV, 74.25

SMPTE 274

30I

1125

1080

2200

1920

10011

HDTV, 74.25

SMPTE 274

30P

1125

1080

2200

1920

11001

HDTV, 74.25

SMPTE 274

25I

1125

1080

2640

1920

11010

HDTV, 74.25

SMPTE 274

25P

1125

1080

2640

1920

11100

HDTV, 74.25

SMPTE 295

25I

1250

1080

2376

1920

11101

HDTV, 74.25

SMPTE 274

24P

1125

1080

2750

1920

10100

HDTV, 74.25

SMPTE 296 (1, 2)

60P

750

720

1650

1280

The HD Only bit when set to a logic-1 locks the CLC031 into

the high definition data range and frequency. In systems

designed to handle only high definition signals, enabling HD

Only reduces the time required for the CLC031 to establish

frequency lock and determine the HD format being pro-

cessed.

The SD Only bit when set to a logic-1 locks the CLC031 into

the standard definition data ranges and frequencies. In sys-

tems designed to handle only standard definition signals,

enabling SD Only reduces the time required for the CLC031

to establish frequency lock and determine the format being

processed. When SD Only and HD Only are set to logic-0,

the device operates in SD/HD mode.

The Framing Mode bit in the Format 0 register and Fram-

ing Enable in the Video Info 0 register combine with Fram-

ing Enable to control the manner in which the CLC031

aligns framing. When Framing Mode and Framing Enable

are both reset, the CLC031 aligns on the first valid TRS

character. If another TRS occurs that is not on a word

boundary, the NSP bit is set until the next TRS that is on a

word boundary occurs. When Framing Mode is set to a

logic-1, the CLC031 operates similarly to the CLC011 when

NSP is tied to FE. An alternative configuration that operates

identically can be achieved with the CLC031 by mapping

NSP as an output and Framing Enable as an input on the

Multifunction I/O bus and externally connecting them. In this

case Framing Mode should be reset to a logic-0. When

Framing Mode is reset and Framing Enable is set, the

CLC031 realigns on every valid TRS. The initial state of

Framing Mode is set following a reset or at power-on.

FORMAT 1 (Address 0Ch)

The CLC031 automatically determines the format of the

incoming serial data. The result of this operation is stored in

the FORMAT 1 register. The Format[4:0] bits identify which

of the many possible video data standards that the CLC031

can process is being received. These format codes follow

the same arrangement as for the Format Set[4:0] bits.

These formats and codes are given in Table 4. Bit Format[4]

when set indicates that HD data is being processed. When

reset, SD data is indicated. Format[3] when set indicates

that PAL data is being processed. When reset NTSC data is

being processed. Format[2:0] correspond with one of the

sub-standards given in the table. Note that the CLC031 does

not distinguish or log the data rate differences between HD

data at 74.25Mhz and 74.25MHz/1.001.

The H, V, and F bits correspond to input TRS data bits 6, 7

and 8, respectively. The meaning and function of this data is

the same for both standard definition (SMPTE 125M) and

high definition (SMPTE 292M luminance and colour differ-

ence) video data. Polarity is logic-1 equals HIGH-true. These

bits are registered for the duration of the applicable field.

TEST 0 REGISTER (Address 0Dh)

The Test Pattern Select bits determine which test pattern is

output when the Test Pattern Generator (TPG) mode or the

Built-in Self-Test (BIST) mode is enabled. Table 5 gives the

codes corresponding to the various test patterns. All HD

colour bar test patterns are inherently BIST data. BIST test

patterns for SD are: NTSC, 27MHz, 4x3 Colour Bars and

PAL, 27MHz, 4x3 PLL Pathological.

The TPG Enable bit when set to a logic-1 enables the Test

Pattern Generator function and built-in self-test (BIST).

The Pass/Fail bit indicates the result of the built-in self-test.

This bit is a logic-1 for a pass condition.

CLC031 Datasheet(PDF) 22 Page - National Semiconductor (TI)

CLC031 Datasheet(HTML) 22 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31

Datasheet Download

Link URL