LTC2440IGN datasheet(12/28 Pages) LINER

12 / 28 page

LTC2440

sn2440, 2440fas

signal may be used as an interrupt for an external

microcontroller. Bit 31 (EOC) can be captured on the first

rising edge of SCK. Bit 30 is shifted out of the device on the

first falling edge of SCK. The final data bit (Bit 0) is shifted

out on the falling edge of the 31st SCK and may be latched

on the rising edge of the 32nd SCK pulse. On the falling

edge of the 32nd SCK pulse, SDO goes HIGH indicating the

initiation of a new conversion cycle. This bit serves as EOC

(Bit 31) for the next conversion cycle. Table 2 summarizes

the output data format.

As long as the voltage on the IN+ and IN– pins is maintained

within the – 0.3V to (VCC + 0.3V) absolute maximum

operating range, a conversion result is generated for any

differential input voltage VIN from –FS = –0.5 • VREF to

+FS = 0.5 • VREF. For differential input voltages greater than

+FS, the conversion result is clamped to the value corre-

sponding to the +FS + 1LSB. For differential input voltages

below –FS, the conversion result is clamped to the value

corresponding to –FS – 1LSB.

SERIAL INTERFACE PINS

The LTC2440 transmits the conversion results and re-

ceives the start of conversion command through a

synchronous 2-wire, 3-wire or 4-wire interface. During

the conversion and sleep states, this interface can be

used to assess the converter status and during the data

output state it is used to read the conversion result and

program the speed/resolution.

Serial Clock Input/Output (SCK)

The serial clock signal present on SCK (Pin 13) is used to

synchronize the data transfer. Each bit of data is shifted out

the SDO pin on the falling edge of the serial clock.

In the Internal SCK mode of operation, the SCK pin is an

output and the LTC2440 creates its own serial clock. In the

External SCK mode of operation, the SCK pin is used as

input. The internal or external SCK mode is selected by tying

EXT (Pin 10) LOW for external SCK and HIGH for internal

SCK.

Serial Data Output (SDO)

The serial data output pin, SDO (Pin 12), provides the

result of the last conversion as a serial bit stream (MSB

first) during the data output state. In addition, the SDO pin

is used as an end of conversion indicator during the

conversion and sleep states.

When CS (Pin 11) is HIGH, the SDO driver is switched to

a high impedance state. This allows sharing the serial

interface with other devices. If CS is LOW during the

convert or sleep state, SDO will output EOC. If CS is LOW

during the conversion phase, the EOC bit appears HIGH on

the SDO pin. Once the conversion is complete, EOC goes

LOW. The device remains in the sleep state until the first

rising edge of SCK occurs while CS = LOW.

Table 2. LTC2440 Output Data Format

Differential Input Voltage

Bit 31

Bit 30

Bit 29

Bit 28

Bit 27

Bit 26

Bit 25

…

Bit 0

VIN*

EOC

DMY

SIG

MSB

VIN* ≥ 0.5 • VREF**

0110

…

0.5 • VREF** – 1LSB

0101

…

0.25 • VREF**

0101

…

0.25 • VREF** – 1LSB

0100

…

0100

…

–1LSB

0011

…

– 0.25 • VREF**

0011

…

– 0.25 • VREF** – 1LSB

0010

…

– 0.5 • VREF**

0010

…

VIN* < –0.5 • VREF**

0001

…

*The differential input voltage VIN = IN+ – IN–. **The differential reference voltage VREF = REF+ – REF–.

APPLICATIO S I FOR ATIO

LTC2440IGN Datasheet(PDF) 12 Page - Linear Technology

LTC2440IGN Datasheet(HTML) 12 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

Datasheet Download

Link URL