Electronic Components Datasheet Search
  English  ▼

X  

MIC23350 Datasheet(PDF) 14 Page - Microchip Technology

Part # MIC23350
Description  3A Step-Down Converter with HyperLight Load® and Output Voltage Select
PDF  28 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  MICROCHIP [Microchip Technology]
Direct Link  http://www.microchip.com
Logo MICROCHIP - Microchip Technology

MIC23350 Datasheet(HTML) 14 Page - Microchip Technology

Back Button MIC23350 Datasheet HTML 10Page - Microchip Technology MIC23350 Datasheet HTML 11Page - Microchip Technology MIC23350 Datasheet HTML 12Page - Microchip Technology MIC23350 Datasheet HTML 13Page - Microchip Technology MIC23350 Datasheet HTML 14Page - Microchip Technology MIC23350 Datasheet HTML 15Page - Microchip Technology MIC23350 Datasheet HTML 16Page - Microchip Technology MIC23350 Datasheet HTML 17Page - Microchip Technology MIC23350 Datasheet HTML 18Page - Microchip Technology Next Button
Zoom Inzoom in Zoom Outzoom out
 14 / 28 page
background image
MIC23350
DS20006126A-page 14
 2019 Microchip Technology Inc.
4.0
FUNCTIONAL DESCRIPTION
4.1
Device Overview
The MIC23350 is a high-efficiency, 3A continuous
current synchronous buck regulator with HyperLight
Load mode. The COT control architecture with auto-
matic HyperLight Load mode provides very high
efficiency at light loads and ultra-fast transient
response.
The MIC23350 output voltage is set by two VSEL
three-state logic pins that can set the output voltage to
nine different values. See Table 4-1.
The 2.4V to 5.5V input voltage operating range makes
the device ideal for single cell Li-Ion battery-powered
applications. The 100% duty cycle capability provides
low dropout operation, extending battery life in portable
systems. The automatic HyperLight Load mode pro-
vides very high efficiency at light loads.
This device focuses on high output voltage accuracy.
Total output error is less than 1.5% over line, load and
temperature.
The MIC23350 buck regulator uses an adaptive COT
control method. The adaptive on-time control scheme
is employed to obtain a nearly constant switching
frequency
in
Continuous
Conduction
mode.
Overcurrent protection is implemented by sensing the
current on both the low-side and high-side internal
power MOSFETs. The device includes an internal soft
start function which reduces the power supply input
surge current at start-up by controlling the output
voltage rise time.
4.2
HyperLight Load Mode (HLL)
The HLL is a power-saving mode. In HLL, the switching
frequency is not constant over the operation current
range, but its average value reduces proportionally to
the load current. This reduces switching and drive
losses and maintains high efficiency as the load current
decreases.
4.3
Enable (EN)
When the EN pin is pulled LOW, the IC is in a
Shutdown state with all internal circuits disabled with
the PG output low. During shutdown, the part typically
consumes 5 µA. When the EN pin is pulled HIGH, the
start-up sequence is initiated.
4.4
Power Good (PG)
The PG output is generally used for power sequencing
where the PG output is tied to the enable output of
another regulator. This technique avoids all the
regulators powering up at the same time, causing large
inrush current.
The PG output is an open drain output. During start-up,
when the output voltage is rising, the PG output goes
high by means of an external pull-up resistor, when the
output voltage reaches 91% of its set value. The PG
threshold has 4% hysteresis so the PG output stays
high until the output voltage falls below 87% of the set
value. A built-in 65 µs blanking time is incorporated to
prevent nuisance tripping.
The pull-up resistor can be connected to VIN, VOUT or
an external source that is less than or equal to VIN. The
PG pin can be connected to another regulator’s enable
pin for outputs sequencing. The PG output is
deasserted as soon as the enable pin is pulled low or
an input undervoltage condition or any other fault is
detected.
4.5
Resistive Discharge
(Soft-Discharge)
To ensure a known output condition when the device is
turned off and then back on, the output is actively
discharged to ground by means of an internal 10
resistor. This prevents the load from powering- up
starting from an undefined condition.
4.6
Output Voltage Setting
The MIC23350 VSEL1 and VSEL2 pins are used to
choose among nine predefined voltage settings: 0.6V,
0.8V, 0.9V, 1.0V, 1.2V, 1.5V, 1.8V, 2.5V, and 3.3V.
These pins can be tied to VIN, GND or left floating. The
relation between VSEL1/VSEL2 and the output voltage is
shown in Table 4-1.
The output voltage sensing pin VOUT should be
connected to the desired point-of-load regulation,
avoiding parasitic resistive drops. It is possible to fine-
tune the desired output voltage by adding a series
resistor on the VOUT pin. This allows slightly higher
output values programming, but should not exceed 5%
deviation from the VSEL selected value.
TABLE 4-1:
OUTPUT VOLTAGE SETTINGS
VSEL2
VSEL1
VOUT
GND
GND
0.6V
GND
OPEN
0.8V
GND
VIN
0.9V
OPEN
GND
1.0V
OPEN
OPEN
1.2V
OPEN
VIN
1.5V
VIN
GND
1.8V
VIN
OPEN
2.5V
VIN
VIN
3.3V



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com