AM29LV065MU101REF datasheet(28/62 Pages) AMD

28 / 62 page

Am29LV065MU

September 12, 2006

DA TA

SH EET

non-erase-suspended sector. After completing a pro-

gramming operation in the Erase Suspend mode, the

system may once again read array data with the same

exception. See “Erase Suspend/Erase Resume Com-

mands” on page 32. for more information.

The system must issue the reset command to return

the device to the read (or erase-suspend-read) mode if

DQ5 goes high during an active program or erase op-

eration, or if the device is in the autoselect mode. See

the next section, Reset Command, for more informa-

tion.

See “Requirements for Reading Array Data” on

page 10 . fo r more info r m ation. See the tabl e,

“Read-Only Operations” on page 42 provides the read

parameters, and Figure 13 shows the timing diagram.

Reset Command

Writing the reset command resets the device to the

read or erase-suspend-read mode. Address bits are

don’t cares for this command.

The reset command may be written between the se-

quence cycles in an erase command sequence before

erasing begins. This resets the device to the read

mode. Once erasure begins, however, the device ig-

nores reset commands until the operation is complete.

The reset command may be written between the

sequence cycles in a program command sequence

before programming begins. This resets the device to

the read mode. If the program command sequence is

written while the device is in the Erase Suspend mode,

writing the reset command returns the device to the

erase-suspend-read mode. Once programming be-

gins, however, the device ignores reset commands

until the operation is complete.

The reset command may be written between the se-

quence cycles in an autoselect command sequence.

Once in the autoselect mode, the reset command

must be written to return to the read mode. If the de-

vice entered the autoselect mode while in the Erase

Suspend mode, writing the reset command returns the

device to the erase-suspend-read mode.

If DQ5 goes high during a program or erase operation,

writing the reset command returns the device to the

read mode (or erase-suspend-read mode if the device

was in Erase Suspend).

Note that if DQ1 goes high during a Write Buffer Pro-

gramming operation, the system must write the

Write-to-Buffer-Abort Reset command sequence to

reset the device for the next operation.

Autoselect Command Sequence

The autoselect command sequence allows the host

system to access the manufacturer and device codes,

and determine whether or not a sector is protected.

Table 10 shows the address and data requirements.

This method is an alternative to that shown in Table 3,

which is intended for PROM programmers and re-

quires V

ID on address pin A9. The autoselect com-

mand sequence may be written to an address that is

either in the read or erase-suspend-read mode. The

autoselect command may not be written while the de-

vice is actively programming or erasing.

The autoselect command sequence is initiated by first

writing two unlock cycles. This is followed by a third

write cycle that contains the autoselect command. The

device then enters the autoselect mode. The system

may read at any address any number of times without

initiating another autoselect command sequence:

■ A read cycle at address XX00h returns the manu-

facturer code.

■ Three read cycles at addresses 01h, 0Eh, and 0Fh

return the device code.

■ A read cycle to an address containing a sector

group address (SA), and the address 02h on A7–A0

returns 01h if the sector group is protected, or 00h

if it is unprotected. (See Table 4 for valid sector ad-

dresses).

The system must write the reset command to return to

the read mode (or erase-suspend-read mode if the de-

vice was previously in Erase Suspend).

Enter SecSi Sector/Exit SecSi Sector

Command Sequence

The SecSi Sector region provides a secured data area

containing an 16-byte random Electronic Serial Num-

ber (ESN). The system can access the SecSi Sector

region by issuing the three-cycle Enter SecSi Sector

command sequence. The device continues to access

the SecSi Sector region until the system issues the

four-cycle Exit SecSi Sector command sequence. The

Exit SecSi Sector command sequence returns the de-

vice to normal operation. Table 10 shows the address

and data requirements for both command sequences.

See also “SecSi (Secured Silicon) Sector Flash

Memory Region” for further information. Note that the

ACC function and unlock bypass modes are not avail-

able when the SecSi Sector is enabled.

Byte Program Command Sequence

Programming is a four-bus-cycle operation. The pro-

gram command sequence is initiated by writing two

unlock write cycles, followed by the program set-up

command. The program address and data are written

next, which in turn initiate the Embedded Program al-

gorithm. The system is not required to provide further

controls or timings. The device automatically provides

internally generated program pulses and verifies the

programmed cell margin. Table 10 shows the address

AM29LV065MU101REF Datasheet(PDF) 28 Page - Advanced Micro Devices

AM29LV065MU101REF Datasheet(HTML) 28 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62

Datasheet Download

Link URL