| Electronic Components Datasheet Search |
|
LT1116CS8 Datasheet(PDF) 6 Page - Linear Technology |
|
|
|||||||||||||||||||||||||||||
LT1116CS8 Datasheet(HTML) 6 Page - Linear Technology |
|
6 / 8 page ![]() LT1116 6 1116fb Common Mode Considerations The LT1116 is specified for a common mode range of 0V to 2.5V with a single 5V supply, and –5V to 2.5V with ±5V supplies. The common mode range is defined as the DC input for which the output responds correctly to small changes in the input differential. Input signals can exceed the positive common mode limit up to the 15V absolute maximum rating without damaging the comparator. There will, however, be an increase in propagation delay of up to 10ns when the input signal switches back into the common mode range. When input signals fall below the negative common mode limit, the internal PN diode formed with the substrate can turn on (resulting in significant charge flow throughout the die). A Schottky clamp diode, between the input and the negative rail, speeds up recov- ery from negative overdrive by preventing the substrate diode from turning on. The zero crossing detector in Figure 1 demonstrates the use of a fast clamp diode. Recovery, from 500mV overdrive below V–, for this circuit is approximately 18ns. Input Characteristics Each input to the LT1116 is buffered with a fast PNP follower—input bias current therefore does not vary significantly throughout the common mode range. When either input exceeds the positive common mode limit, the bias current drops to zero. Inputs that fall more than one diode and drop below V– will forward bias the substrate or clamp diode, causing large input current to flow. Single ended input resistance is about 5M Ω, and remains roughly constant over the input common mode range. The common mode resistance is about 2.5M Ω with zero differential input voltage, and does not change significantly with the absolute value of differential input. Effective input capacitance, typically 5pF, is determined by measuring the resulting change in propagation delay for a 1k Ω change in source resistance. Latch Pin Dynamics The internal latch uses local regenerative feedback to shorten set-up and hold times. Driving the latch pin high retains the output state. The latch pin floats to a high state when disconnected, so it must be driven low for flow-through operation. The set-up time required to guarantee detecting a given transition of the inputs is 2ns. The inputs must also remain stable for a 2ns hold time after latch is asserted. New data will appear at the output approximately 10ns to 12ns after the latch goes low. The latch pin has no built-in hysteresis, and is designed to be driven from TTL or CMOS logic gates. Additional Information Linear Technology’s Application Note 13 provides an extensive discussion of design techniques for high speed comparators. Figure 1. The Zero Crossing Detector Terminates the Transmission Line At Its 50 Ω Characteristic Impedance. Negative Inputs Should Not Fall Below –2V to keep the Signal Current Within the Clamp Diode’s Maximum Forward Rating. Positive Inputs Should not Exceed the Devices Absolute Maximum Ratings nor the Power Rating on the Terminating Resistor Figure 2. This Single Supply Crystal Oscillator Utilizes Crystals From 10MHz To 15MHz Without Component Changes APPLICATIO S I FOR ATIO Fast Zero Crossing Detector Single Supply Crystal Oscillator 10MHZ to 15MHz LT1116 • AI01 Q Q 5V CABLE 1N5712 VIN RS 50 Ω RT 50 Ω – LT1116 + – LT1116 • AI02 Q OUTPUT 2k Ω 1k Ω 1k Ω 24pF 5V 10 TO 15MHz AT CUT 5V Q – LT1116 + – |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |