LT1206 datasheet(3/16 Pages) LINER

3 / 16 page

LT1206

1206fa

Note 1: Stresses beyond those listed under Absolute Maximum Ratings

may cause permanent damage to the device. Exposure to any Absolute

Maximum Rating condition for extended periods may affect device

reliability and lifetime.

Note 2: Applies to short circuits to ground only. A short circuit between

the output and either supply may permanently damage the part when

operated on supplies greater than ± 10V.

The

● denotes the speciﬁcations which apply over the full operating

temperature range, otherwise speciﬁcations are at TA = 25°C. VCM = 0, ±5V ≤ VS ≤ 15V, pulse tested, VS/D = 0V, unless otherwise noted.

ELECTRICAL CHARACTERISTICS

SYMBOL

PARAMETER

CONDITIONS

MIN

TYP

MAX

UNITS

Input Noise Voltage Density

f = 10kHz, RF = 1k, RG = 10Ω, RS = 0Ω

3.6

nV/√Hz

+in

Input Noise Current Density

f = 10kHz, RF = 1k, RG = 10Ω, RS = 10k

pA/√Hz

–in

Input Noise Current Density

f = 10kHz, RF = 1k, RG = 10Ω, RS = 10k

pA/√Hz

RIN

Input Resistance

VIN = ±12V, VS = ±15V

VIN = ±2V, VS = ±5V

●

1.5

0.5

CIN

Input Capacitance

VS = ±15V

Input Voltage Range

VS = ±15V

VS = ±5V

●

±12

±2

±13.5

±3.5

CMRR

Common Mode Rejection Ratio

VS = ±15V, VCM = ±12V

VS = ±5V, VCM = ±2V

●

Inverting Input Current Common Mode

Rejection

VS = ±15V, VCM = ±12V

VS = ±5V, VCM = ±2V

●

0.1

µA/V

PSRR

Power Supply Rejection Ratio

VS = ±5V to ±15V

●

Noninverting Input Current Power Supply

Rejection

VS = ±5V to ±15V

●

500

nA/V

Inverting Input Current Power Supply

Rejection

VS = ±5V to ±15V

●

0.7

µA/V

Large-Signal Voltage Gain

VS = ±15V, VOUT = ±10V, RL = 50Ω

VS = ±5V, VOUT = ±2V, RL = 25Ω

●

ROL

Transresistance,

ΔVOUT/ΔIIN–

VS = ±15V, VOUT = ±10V, RL = 50Ω

VS = ±5V, VOUT = ±2V, RL = 25Ω

●

100

260

200

VOUT

Maximum Output Voltage Swing

VS = ±15V, RL = 50Ω

●

±11.5

±10.0

±12.5

VS = ±15V, RL = 25Ω

●

±2.5

±2.0

±3.0

IOUT

Maximum Output Current

RL = 1Ω

●

250

500

1200

Supply Current

VS = ±15V, VS/D = 0V

●

Supply Current, RS/D = 51k (Note 4)

VS = ±15V

Positive Supply Current, Shutdown

VS = ±15V, VS/D = 15V

●

200

µA

Output Leakage Current, Shutdown

VS = ±15V, VS/D = 15V

●

µA

Slew Rate (Note 5)

AV = 2

400

900

V/µs

Differential Gain (Note 6)

VS = ±15V, RF = 560Ω, RG = 560Ω, RL = 30Ω

0.02

Differential Phase (Note 6)

VS = ±15V, RF = 560Ω, RG = 560Ω, RL = 30Ω

0.17

Deg

Small-Signal Bandwidth

VS = ±15V, Peaking ≤ 0.5dB,

RF = RG = 620Ω, RL = 100Ω

MHz

VS = ±15V, Peaking ≤ 0.5dB,

RF = RG = 649Ω, RL = 50Ω

MHz

VS = ±15V, Peaking ≤ 0.5dB,

RF = RG = 698Ω, RL = 30Ω

MHz

VS = ±15V, Peaking ≤ 0.5dB,

RF = RG = 825Ω, RL = 10Ω

MHz

Note 3: Commercial grade parts are designed to operate over the

temperature range of –40°C to 85°C but are neither tested nor guaranteed

beyond 0°C to 70°C. Industrial grade parts tested over –40°C to 85°C are

available on special request. Consult factory.

Note 4: RS/D is connected between the shutdown pin and ground.

Note 5: Slew rate is measured at ±5V on a ± 10V output signal while

operating on ±15V supplies with RF = 1.5k, RG = 1.5k and RL = 400Ω.

Note 6: NTSC composite video with an output level of 2V.

LT1206 Datasheet(PDF) 3 Page - Linear Technology

LT1206 Datasheet(HTML) 3 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Datasheet Download

Link URL