CPT-DINAV61LS2AX datasheet(4/13 Pages) ETC2

4 / 13 page

Specifications are subject to change without notice

CPT-DINADS110706

CPT-DIN

AC/DC voltage

90 to 260VAC/DC

18 to 60VAC/DC

Power consumption

AC: 2.5 VA

DC: 2W

Power Supply Specifications

4kVAC RMS between

power supply and

RS485/RS232/programming

port (RJ12)

Dielectric strength

4kVACRMS (for 1 min)

EMC

Emissions

EN61000-6-3, EN60688

residential environment,

commerce and light industry

Immunity

EN61000-6-2

industrial environment.

Pulse voltage (1.2/50µs)

EN61000-4-5

Safety standards

IEC60664, IEC61010-1

EN60664, EN61010-1

Mesurement standards

IEC60688, EN60688,

EN62053-31, EN62053-23

Approvals

CE, cURus

Connections 5(6) A

Screw-type

Max cable cross sect. area

2.5 mm2

Housing

Dimensions (WxHxD)

45 x 83.5 x 98.5 mm

Material

ABS

self-extinguishing: UL 94 V-0

Mounting

DIN-rail

Protection degree

IP20

Weight

Approx. 200 g (pack. incl.)

Front LED’s

Power on

Green

Diagnostics

RS485/RS422/RS232

TX data (Green)

RX data (Red)

Dupline bus

TX data (Green)

RX data (Red)

Alarm outputs

1st output activation (Green)

2nd output activation (Red)

Pulse outputs

1st output activation (Green)

2nd output activation (Red)

Analogue outputs

Output signal within the

programmed scale (Green)

Output signal exceeding

110% of full scale (Red)

Operating

0° to +50°C (32° to 122°F)

temperature

(RH < 90% non condensing)

Storage

-10° to +60°C (14° to 140°F)

temperature

(RH < 90% non condensing)

Overvoltage category

Cat. III (IEC 60664, EN60664)

Insulation (for 1 minute)

4kVACRMS

between measuring

inputs and power supply.

4kVAC/DC @ I

≥ 3mA

between measuring inputs

and RS485/RS232/

programming port (RJ12)

General Specifications

- W dmd max, VA dmd max,

A1 max, A2 max, A3 max,

WL1 max, WL2 max, WL3 max,

W sys max, A1 dmd max,

A2 dmd max, A3 dmd max,

VA sys dmd max,

W sys dmd max, PF 1 min,

PF 2 min, PF 3 min

- all the counters: total kWh,

partial kWh, total kvarh,

partial kvarh, hour counters

- reset of all the above

mentioned variables in a

single command

Alarms

Working mode

“OR” or “AND” or

“OR+AND” functions (see

“Alarm parameter and logic”

page). The user can freely

program up to 16 total

alarms. (out1+out2).

The alarms

can be connected to any

variables available in the

table “List of the variables

that can be connected to”

Reset

The following resets are

available by means of the

configuration software:

- all the maximum/min values:

Software functions (cont.)

CPT-DINAV61LS2AX Datasheet(PDF) 4 Page - List of Unclassifed Manufacturers

CPT-DINAV61LS2AX Datasheet(HTML) 4 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13

Datasheet Download

Link URL