Switch Type

Inbuilt Mains Rated DALI Switch

A Terminal input has been provided to allow the wiring of a Main rated switch

input. This input can be programmed to switch any controlled area when using a

DALI-2 compliant control system. This input supports IEC62386-301

(momentary or rocker switches), IEC62386-302 (on /off switches) and

IEC62386-303 (mains rated sensor inputs).

System Max Wattage

30 W

Working Temp Range

-20 to 40 °C

LAMP

Macadam Steps (SDCM)

3-step MacAdam Ellipse

CCT Configuration

Single

Colour Rendering Index (CRI)

>84

Lamp/LED Current

850 mA

Lamp/LED voltage

36 V

LED LIFETIME

LED Lifetime

>102000 hrs

This is the Reported LED Lifetime in Hours based on TM-21. Ektor does not list

the projected or calculated LED lifetime, which is normally longer as TM-21

Addendum B explicitly states "The Calculated and Projected Lp(Dk) are not to be

reported". This Lifetime refers to the life of a single LED however the system life

is longer since the probability and binomial distribution of all LEDs in the system

means that the average led is performing above the specification and

compensates for the LEDs falling below.

Ambient Temp (°C)

25 °C

40 °C

L90B10

55000 hrs

55000 hrs

This rating defines the performance of the led within its lifetime. L relates to

lumen depreciation, where the proceeding number gives the resultant lumen

output at the end of it reported lifetime. L70, would mean 30% lumen

depreciation which means 70% of its initial output and is tested accordingly to

TM-21. The B part refers to failures, which can be define as the percentage of

LEDs which fall below the L value in the projected lifetime. A value of B10 refers

to 10% failure and a value of B50 refers to 50% failure. After the defined lifetime,

the system will reach the defined lumen depreciation and the average led

failures is defined by the B rating. The B rating is defined in and tested to

IEC62717.

TM-21 Test Hours

17000 hrs

COLOUR TEMPERATURE

CCT

4000 K

Luminaire Lumens

4100 lm

All photometric data has a tolerance of ±10%. Luminaire lumens refers to the

exit lumens or delivered lumens from the luminaire.

DRIVER

Dimmable

Yes

Driver Included

Yes

Integrated Driver

No

Driver Mode

Constant Current

Driver Type

DALI DT6 LED Driver

DALI DT6 ~ Includes DALI-2 Driver with full support for DT6 allowing flicker free

dimming with compliant DALI-2 Application controllers.

Power Monitoring

DALI Device type 51 power

monitoring

Inbuilt DALI-2 support for Device type 51 - Power monitoring for use with DALI-2

compliant control systems which allows the reporting of the products total

power consumption for power aggregation and measurements.

Wiring Type

Re-wireable terminal block (6

pin)

PSTLM

0.08

Short Term Light Modulation (PstLM): The requirement is that PstLM should be

less than or equal to 1.0. This metric measures the short-term flicker severity

and ensures that flicker is not perceptible or is at a level that does not cause

discomfort or health issues.

SVM

0.018

Stroboscopic Visibility Measure (SVM): The requirement for SVM is that it

should be less than or equal to 0.4. The SVM metric assesses the visibility of the

stroboscopic effect, which can make moving objects appear to be stationary or

moving in discrete steps, thus ensuring that this effect is minimized in lighting

environments to prevent visual discomfort and safety hazards.

SENSOR (S SUFFIX)

Adjustable Detection Area /

Sensitivity

Yes

Adjustable Hold Time

Yes

Adjustable Standby Level

Yes

Adjustable Standby Period

Yes

Corridor Function

Yes

Dawn Reset

No

Detection Range

10 m

Dusk Mode

No

Lux Adjustment

No

Manual Override

Yes

Sensor Communication

DALI 2

Inbuilt DALI-2 Sensor for use with DALI-2 Compliant control systems. Some

features and functions are only available for use with DALI-2 Application

controllers which support the features. This product also supports a standalone

mode for limited use without a DALI-2 application controller.

Sensor Type

Microwave

Switched Output

No

Time Delay

Via DALI

Information is subject to change without prior notice. Images are for illustrative purposes only. E&OE