Application Notes

North America (USA): 1-888-41-ASTEC

Europe (UK): 44(1384)842-211

Asia (HK): 852-2437-9662

Adjusting the Output Voltage of the ATH06T033

& ATH06T05 Wide-Output Adjust Power Modules

value higher than 0.8 V. The adjustment range of the

the ATH06T05-9xx (5-V input) from 0.8 V to 3.6 V. The

adjustment method requires the addition of a single

the preferred value of the external resistor for a number

of standard voltages, along with the actual output volt-

age that this resistance value provides.

For other output voltages the value of the required resistor

can either be calculated using the following formula, or

simply selected from the range of values given in Table 1-2.

Figure 1-1 shows the placement of the required resistor.

= 10 k

Ω ·

0.8 V

– 2.49 k

Ω

Notes:

1. Modules that operate from a 3.3-V input bus should

not be adjusted higher than 2.5 V.

2. Use a 0.1 W resistor. The tolerance should be 1 %, with

temperature stability of 100 ppm/°C (or better). Place

the resistor as close to the regulator as possible. Connect

the resistor directly between pins 5 and 1 using dedicated

PCB traces.

the stability of the regulator.

0.800

Open

0.825

318 k

Ω

0.850

158 k

Ω

0.875

104 k

Ω

0.900

77.5 k

Ω

0.925

61.5 k

Ω

0.950

50.8 k

Ω

0.975

43.2 k

Ω

1.000

37.5 k

Ω

1.025

33.1 k

Ω

1.050

29.5 k

Ω

1.075

26.6 k

Ω

1.100

24.2 k

Ω

1.125

22.1 k

Ω

1.150

20.4 k

Ω

1.175

18.8 k

Ω

1.200

17.5 k

Ω

1.225

16.3 k

Ω

1.250

15.3 k

Ω

1.275

14.4 k

Ω

1.300

13.5 k

Ω

1.325

12.7 k

Ω

1.350

12.1 k

Ω

1.375

11.4 k

Ω

1.400

10.8 k

Ω

1.425

10.3 k

Ω

1.450

9.82 k

Ω

1.475

9.36 k

Ω

1.50

8.94 k

Ω

1.55

8.18 k

Ω

1.60

7.51 k

Ω

1.65

6.92 k

Ω

1.70

6.4 k

Ω

1.75

5.93 k

Ω

1.80

5.51 k

Ω

1.85

5.13 k

Ω

1.90

4.78 k

Ω

1.95

4.47 k

Ω

698

Ω

3.309V

2.5 V

2.21 k

Ω

2.502 V

2 V

4.12 k

Ω

2.010 V

1.8 V

5.49 k

Ω

1.803 V

1.5 V

8.87 k

Ω

1.504 V

1.2 V

17.4 k

Ω

1.202 V

1 V

36.5 k

Ω

1.005 V

0.8 V

Open

0.8 V

ATH06T033 & ATH06T05 Series

Table 1-2; Output Voltage Set-Point Resistor Values

2.00

4.18 k

Ω

2.05

3.91 k

Ω

2.10

3.66 k

Ω

2.15

3.44 k

Ω

2.20

3.22 k

Ω

2.25

3.03 k

Ω

2.30

2.84 k

Ω

2.35

2.67 k

Ω

2.40

2.51 k

Ω

2.45

2.36 k

Ω

2.50

2.22 k

Ω

2.55

2.08 k

Ω

2.60

1.95 k

Ω

2.65

1.83 k

Ω

2.70

1.72 k

Ω

2.75

1.61 k

Ω

2.80

1.51 k

Ω

2.85

1.41 k

Ω

2.90

1.32 k

Ω

2.95

1.23 k

Ω

3.00

1.15 k

Ω

3.05

1.07 k

Ω

3.10

988

Ω

3.15

914

Ω

3.20

843

Ω

3.25

775

Ω

3.30

710

Ω

3.35

647

Ω

3.40

587

Ω

3.45

529

Ω

3.50

473

Ω

3.55

419

Ω

3.60

367

Ω

V

IN

C

IN

100 µF

(Required)

C

OUT

100 µF

(Optional)

GND

V

OUT

R

SET

1 %

0.1 W

PTH05050W

14

6

3

3

2

Track

V

IN

V

O

GND

Inhibit

ATH06T05-9J