ISO1430DWR datasheet(10/49 Pages) TI2

10 / 49 page

7.10 Electrical Characteristics: Receiver

All typical specs are at VCC1=3.3V, VCC2=5V, TA=27°C, (Min/Max specs are over recommended operating conditions unless

otherwise noted)

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

Ii1

Bus input current

VDE = 0 V, VCC2 = 0 V or VCC2 = 5.5 V, 500-kbps

devices, VI = –7 V or VI = 12 V, other input at 0 V

–100

125

µA

Ii1

Bus input current

VDE = 0 V, VCC2 = 0 V or VCC2 = 5.5 V, 12-Mbps and

50-Mbps devices, VI = –7 V or VI = 12 V,

other input at 0 V

–100

125

µA

Ii1

Bus input current

VDE = 0 V, VCC2 = 0 V or VCC2 = 5.5 V, 500-kbps

devices, VI = –15 V or VI = 15 V, other input at 0 V

-200

125

µA

Ii1

Bus input current

VDE = 0 V, VCC2 = 0 V or VCC2 = 5.5 V, 12-Mbps and

50-Mbps devices, VI = –15 V or VI = 15 V,

other input at 0 V

-200

125

µA

VTH+

Positive-going input threshold voltage

–15 V ≤ VCM ≤ 15 V

See (1)

-100

–10

–7 V ≤ VCM ≤ 12 V

See (1)

-100

–20

VTH–

Negative-going input threshold

voltage

–15 V ≤ VCM ≤ 15 V

–200

–130

See (1)

Vhys

Input hysteresis (VTH+ – VTH–)

–15 V ≤ VCM ≤ 15 V

VOH

Output high voltage on the R pin

VCC1=5V ± 10%, IOH = –4 mA, VID = 200 mV

VCC1 – 0.4

VCC1=3.3V ± 10%, IOH = –2 mA, VID = 200 mV

VCC1 – 0.3

VCC1=2.5V ± 10%, 1.8V+/-5%, IOH = –1 mA, VID =

200 mV

VCC1 – 0.2

VOL

Output low voltage on the R pin

VCC1=5V ± 10%, IOL = 4 mA, VID = –200 mV

0.4

VCC1=3.3V ± 10%, IOL = 2 mA, VID = –200 mV

0.3

VCC1=2.5V ± 10%, 1.8V ± 5%, IOL = 1 mA, VID =

–200 mV

0.2

IOZ

Output high-impedance current on

the R pin

VR = 0 V or VR = VCC1, VRE = VCC1

–1

µA

Input current on the RE pin

VRE = 0 V or VRE = VCC1

–10

µA

CMTI

Common-mode transient immunity

VCC1=1.71 V to 5.5 V, VID = 1.5 V or -1.5 V, VCM =

1200 V, ISO141x, See Figure 8-4

100

kV/µs

CMTI

Common-mode transient immunity

VCC1=1.71 V to 5.5 V, VID = 1.5 V or -1.5 V, VCM =

1200 V, ISO143x, See Figure 8-4

100

kV/µs

CMTI

Common-mode transient immunity

VCC1=2.25 V to 5.5 V, VID = 1.5 V or -1.5 V, VCM =

1200 V, ISO145x, See Figure 8-4

100

kV/µs

(1)

Under any specific conditions, VTH+ is verified to be at least Vhys higher than VTH–.

ISO1450, ISO1452, ISO1410, ISO1412, ISO1430, ISO1432

SLLSF22H – APRIL 2018 – REVISED JUNE 2024

www.ti.com

Submit Document Feedback

Product Folder Links: ISO1450 ISO1452 ISO1410 ISO1412 ISO1430 ISO1432

ISO1430DWR Datasheet(PDF) 10 Page - Texas Instruments

ISO1430DWR Datasheet(HTML) 10 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49

Datasheet Download

Link URL