M32C83T datasheet(155/527 Pages) RENESAS

155 / 527 page

Page 132

13. DMACII

)

(

a=-1

b=0

c=1

d=0

e=0

m=1

First DMAC II transfer

t=6+26x1+4x1=36 cycles

Second DMAC II transfer t=6+26x1+4x0=32 cycles

Transfer counter = 2

Decrement a transfer counter

Transfer counter = 1

Program

DMAC II transfer

(First time)

DMAC II transfer

(Second time)

cycles

Processing the end-of-transfer

interrupt

DMAC II transfer request

Decrement a transfer counter

Transfer counter = 0

cycles

DMAC II transfer request

If the end-of-transfer interrupt (transfer counter = 2) occurs with no chained transfer function

after a memory-to-memory transfer occurs with a relocatable source address, fixed destination address,

single transfer and double transfer:

13.5 Execution Time

DMAC II execution cycle is calculated by the following equations:

Multiple transfers: t = 21 + (11 + b + c) x k cycles

Other than multiple transfers: t = 6 + (26 + a + b + c + d) x m + (4 + e) x n cycles

a: If IMM = 0 (source of transfer is immediate data), a = 0;

if IMM = 1 (source of transfer is memory), a = –1

b: If UPDS = 1 (source transfer address is a relocatable address), b = 0;

if UPDS = 0 (source transfer address is a fixed address), b = 1

c: If UPDD = 1 (destination transfer address is a relocatable address), c = 0;

if UPDD = 0 (destination transfer address is a fixed address), c = 1

d: If OPER = 0 (calculation function is not selected), d = 0;

if OPER = 1 (calculation function is selected) and UPDS = 0 (source of transfer is immediate data or fixed

address memory), d = 7;

if OPER = 1 (calculation function is selected) and UPDS = 1 (source of transfer is relocatable address

memory), d = 8

e: If CHAIN = 0 (chained transfer is not selected), e = 0; if CHAIN = 1 (chained transfer is selected), e = 4

m: BRST = 0 (single transfer), m = 1; BRST = 1 (burst transfer), m = the value set in COUNT

n: If COUNT = 1, n = 0; if COUNT = 2 or more, n = 1

k: Number of transfers set in the CNT2 to CNT0 bits

The equations above are approximations. The number of cycles may change with CPU state, bus wait

state, and DMAC II index allocation.

The first instruction from the end-of-transfer interrupt service routine is executed in the 8th cycle after the

DMAC II transfer is completed.

Figure 13.5 Transfer Cycle

When an interrupt request which acts as a DMAC II transfer request factor and another interrupt request

_______

with higher priority (e.g., NMI or watchdog timer) are generated simultaneously, the interrupt with higher

priority takes precedence over the DMAC II transfer. The pending DMAC II transfer starts after the interrupt

sequence has been completed.

M32C83T Datasheet(PDF) 155 Page - Renesas Technology Corp

M32C83T Datasheet(HTML) 155 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL