LTC2902-2IGN datasheet(11/16 Pages) LINER

11 / 16 page

LTC2902

2902f

APPLICATIO S I FOR ATIO

In the negative adjustable mode, the noninverting input on

the V4 comparator is connected to ground (Figure 6). The

tap point on an external resistive divider, connected be-

tween the negative voltage being sensed and the VREF pin,

is connected to the high impedance inverting input (V4).

VREF provides the necessary level shift required to operate

at ground. The trip voltage is calculated from:

TRIP

REF









–;

1 210

T0,T1 Low (5% Tolerance Mode)

Once the resistor divider is set in the 5% tolerance mode,

there is no need to change the divider for the other

tolerance modes (7.5%, 10%, 12.5%) because VREF is

scaled accordingly, moving the trip point in – 2.5%

increments.

In a negative adjustable application, the minimum value

for R4 is limited by the sourcing capability of VREF (±1mA).

With no other load on VREF, R4 (minimum) is:

1.21V

÷ 1mA = 1.21kΩ

Tables 2 and 3 offer suggested 1% resistor values for

various adjustable applications.

Although all four supply monitor comparators have built-in

glitch immunity, bypass capacitors on V1 and V2 are

recommended because the greater of V1 or V2 is also the

VCC for the chip. Filter capacitors on the V3 and V4 inputs

are allowed.

Power-Down

On power-down, once any of the VX inputs drop below

their threshold, RST and COMPX are held at a logic low.

A logic low of 0.4V is guaranteed until both V1 and V2

drop below 1V. If the bandgap reference becomes invalid

(VCC < 2V typ), the part will reprogram once VCC rises

above 2.4V (max).

Monitor Output Rise and Fall Time Estimation

All of the outputs (RST, COMPX) have strong pull-down

capability. If the external load capacitance (CLOAD) for a

Table 2. Suggested 1% Resistor Values for the ADJ Inputs

VSUPPLY (V)

VTRIP (V)

R3 (k

Ω)

R4 (k

Ω)

11.25

2150

100

9.4

1780

100

7.5

1400

100

7.5

1300

100

5.6

1020

100

4.725

845

100

3.3

3.055

511

100

2.82

464

100

2.5

2.325

365

100

1.8

1.685

237

100

1.5

1.410

182

100

1.2

1.120

124

100

0.933

86.6

100

0.9

0.840

68.1

100

Table 3. Suggested 1% Resistor Values for the –ADJ Input

VSUPPLY (V)

VTRIP (V)

R3 (k

Ω)

R4 (k

Ω)

–2

–1.87

187

121

–5

–4.64

464

121

–5.2

–4.87

487

121

–10

–9.31

931

121

–12

–11.30

1130

121

Figure 5. Setting the Positive Adjustable Trip Point

Figure 6. Setting the Negative Adjustable Trip Point

–

2902 F06

VREF

VTRIP

LTC2902

–

0.5V

5% TOLERANCE MODE

2902 F05

V3 OR V4

VTRIP

LTC2902

LTC2902-2IGN Datasheet(PDF) 11 Page - Linear Technology

LTC2902-2IGN Datasheet(HTML) 11 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Datasheet Download

Link URL