Electronic Components Datasheet Search
  English  ▼

X  

PCA9574 Datasheet(PDF) 13 Page - NXP Semiconductors

Part # PCA9574
Description  8-bit I2C-bus and SMBus, level translating, low voltage GPIO with reset and interrupt
PDF  32 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  NXP [NXP Semiconductors]
Direct Link  http://www.nxp.com
Logo NXP - NXP Semiconductors

PCA9574 Datasheet(HTML) 13 Page - NXP Semiconductors

Back Button PCA9574 Datasheet HTML 9Page - NXP Semiconductors PCA9574 Datasheet HTML 10Page - NXP Semiconductors PCA9574 Datasheet HTML 11Page - NXP Semiconductors PCA9574 Datasheet HTML 12Page - NXP Semiconductors PCA9574 Datasheet HTML 13Page - NXP Semiconductors PCA9574 Datasheet HTML 14Page - NXP Semiconductors PCA9574 Datasheet HTML 15Page - NXP Semiconductors PCA9574 Datasheet HTML 16Page - NXP Semiconductors PCA9574 Datasheet HTML 17Page - NXP Semiconductors Next Button
Zoom Inzoom in Zoom Outzoom out
 13 / 32 page
background image
PCA9574_2
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 02 — 27 July 2009
13 of 32
NXP Semiconductors
PCA9574
8-bit I2C-bus and SMBus, level translating, low voltage GPIO
5. Once the right byte has been sent and correctly acknowledged, the master sends a
STOP command to end the Software Reset sequence: the PCA9574 then resets to
the default value (power-up value) and is ready to be addressed again within the
specified bus free time. If the master sends a Repeated START instead, no reset is
performed. The I2C-bus master must interpret a non-acknowledge from the PCA9574
(at any time) as a ‘Software Reset Abort’. The PCA9574 does not initiate a software
reset.
7.9 Interrupt output (INT)
The open-drain active LOW interrupt is activated when one of the port pins changes state
and the port pin is configured as an input and the interrupt on it is not masked. The
interrupt is deactivated when the port pin input returns to its previous state or the Input
Port register is read. It is highly recommended to program the MSK register, and the CFG
registers during the initialization sequence after power-up, since any change to them
during Normal mode operation may cause undesirable interrupt events to happen.
Remark: Changing an I/O from an output to an input may cause a false interrupt to occur
if the state of the pin does not match the contents of the Input port register. Only a read of
the Input port register that contains the bit(s) image of the input(s) that generated the
interrupt clears the interrupt condition.
7.10 Standby
The PCA9574 goes into standby when the I2C-bus is idle. Standby supply current is lower
than 1.0
µA (typical).
8.
Characteristics of the I2C-bus
The I2C-bus is for 2-way, 2-line communication between different ICs or modules. The two
lines are a serial data line (SDA) and a serial clock line (SCL). Both lines must be
connected to a positive supply via a pull-up resistor when connected to the output stages
of a device. Data transfer may be initiated only when the bus is not busy.
8.1 Bit transfer
One data bit is transferred during each clock pulse. The data on the SDA line must remain
stable during the HIGH period of the clock pulse as changes in the data line at this time
will be interpreted as control signals (see Figure 8).
Fig 8.
Bit transfer
mba607
data line
stable;
data valid
change
of data
allowed
SDA
SCL



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com