| Electronic Components Datasheet Search |
|
MX214P Datasheet(PDF) 4 Page - CML Microcircuits |
|
|
|||||||||||||||||||||||||||||
MX214P Datasheet(HTML) 4 Page - CML Microcircuits |
|
4 / 17 page ![]() Variable Split Band Inverter 4 MX214/224 1998 MX-COM, Inc. www.mxcom.com Tel: 800 638 5577 336 744 5050 Fax: 336 744 5054 Doc. # 20480112.002 4800 Bethania Station Road, Winston-Salem, NC 27105-1201 USA All trademarks and service marks are held by their respective companies. 2. Signal List MX214 Pin No. MX224 Pin No. Signal Name Description J/P LH J/P LH 7 1 1 1 Xtal/Clock Input to the clock oscillator inverter. A 1MHz crystal input or externally derived 1MHz clock is injected here. 82 2 2 Xtal Output of the clock oscillator inverter. 9 3 Serial Data Input This pin is used to input an 8-bit word representing the digital control functions. This word is loaded using the serial data clock and in input in the following sequence: MUTE, CLEAR, Tx / Rx , A0, A1, A2, A3, A4. The Latch / Load is operated on the completion. Reference the timing diagram in Figure 8. 3 – A4 4 – A3 5 – A2 6 – A1 7 – A0 3 – A4 4 – A3 5 – A2 6 – A1 7 – A0 Programming Inputs In parallel mode, these five digital inputs define the split point frequency. Each of the 5 input pins has a 1M internal pull-up resistor. See Table 4 for programming information. 88 Tx / Rx This digital input selects the Receive and Transmit paths and configures upperband and lowerband filter bandwidths while setting the CTCSS highpass filter position on the signal path. See Table 2, Figure 6, and Figure 7. 1M internal pull-up resistor (Rx). 13 8 Serial / Parallel This pin must be connected to VSS for serial loading. Internal 1M pull-up resistor. 9 9 Clear/Scramble This digital input puts the device into ‘Clear’ or ‘Scramble’ mode by controlling the application of carrier frequency to the Upper and Lower band balanced modulators. In ‘Scramble’ mode, the balanced modulator carrier frequency values are selected by the split point address A0-A4. See Table 4. In ‘Clear’ mode, the carriers are disabled and the balanced modulators are bypassed internally, i.e. the lower band signal is not added to the output signal. 1MHz internal pull-up resistor (Clear). 10 10 Enable/Mute This digital function is used to disable the Receive or the Transmit signal paths for rolling code synchronization while maintaining bias conditions. Synchronization data can be transmitted during the Mute periods, as is done in the MX1204 VSB Scrambler Module. 1M Internal pull-up resistor (Enable) 14 10 Serial Clock Input This is the externally applied data clock frequency used to shift input data along in devices wired in the Serial-loading mode. One full data clock cycle is required to shift one data bit completely into the register. See Timing Diagram Figure 8. 1M Internal pull-up resistor. |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |