tw

ns

Pulse duration

Setup time before CLK

active transition†

Without C-array

TIBPLS506AC

13

× 97 × 8 FIELD-PROGRAMMABLE LOGIC SEQUENCER

SRPS003C – D3090, DECEMBER 1987 – REVISED NOVEMBER 1995

POST OFFICE BOX 655303

5

absolute maximum ratings over operating free-air temperature range (unless otherwise noted)

7 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Input voltage (see Note 2)

5.5 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Voltage applied to disabled output (see Note 2)

5.5 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating free-air temperature range

0

°C to 75°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Storage temperature range

– 65

°C to 150°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

NOTE 2: These ratings apply except when programming pins during a programming cycle or during diagnostic testing.

recommended operating conditions

MIN

NOM

MAX

UNIT

VCC

Supply voltage

4.75

5

5.25

V

VIH

High-level input voltage, VCC = 5.25 V

2

5.5

V

VIL

Low-level input voltage, VCC = 4.75 V

0.8

V

IOH

High-level output current

– 3.2

mA

IOL

Low-level output current

16

mA

Clock high

6

Clock low

6

Input or feedback to S/R

↑ inputs

12

tsu

Input or feedback to S/R

↓ inputs‡

20

ns

Input or feedback to S/R inputs

With C-array

25

th

Hold time after CLK

Input or feedback to S/R inputs

0

ns

TA

Operating free-air temperature

0

25

75

°C

† The active edge of CLK is determined by the programmed state of CLK polarity fuse.

‡ See the OR term loading section and Figure 3.

electrical characteristics over recommended operating free-air temperature range (unless

otherwise noted)

PARAMETER

TEST CONDITIONS

MIN

TYP§

MAX

UNIT

VIK

VCC = 4.75 V,

II = – 18 mA

– 1.2

V

VOH

VCC = 4.75 V,

IOH = – 3.2 mA

2.4

3

V

VOL

VCC = 4.75 V,

IOL = 16 mA

0.37

0.5

V

IOZH

VCC = 5.25 V,

VO = 2.7 V

20

µA

IOZL

VCC = 5.25 V,

VO = 0.4 V

–20

µA

II

VCC = 5.25 V,

VI = 5.5 V

0.1

mA

IIH

VCC = 5.25 V,

VI = 2.7 V

20

µA

IIL

VCC = 5.25 V,

VI = 0.4 V

– 0.25

mA

IO¶

VCC = 5.25 V,

VO = 0.5 V

–30

–130

mA

ICC

VCC = 5.25 V,

See Note 3,

Outputs open

156

210

mA

Ci

f = 1 MHz,

VI = 2 V

7

pF

Co

f = 1 MHz,

VO = 2 V

11

pF

Cclk

f = 1 MHz,

VCLK = 2 V

14

pF

§ All typical values are at VCC = 5 V, TA = 25°C.

¶ This parameter approximates IOS. The condition VO = 0.5 V takes tester noise into account. Not more than one output should be shorted at a

time and duration of the short circuit should not exceed one second.

NOTE 3: When the clock is programmed for negitive edge, then VI = 4.75 V. When the clock is programmed for positive edge, then VI = 0.