| Electronic Components Datasheet Search |
|
46121 Datasheet(PDF) 7 Page - Tyco Electronics |
|
|
|||||||||||||||||||||||||||||
46121 Datasheet(HTML) 7 Page - Tyco Electronics |
|
7 / 10 page ![]() 408-1559 Hand Crimping Tools 7 of 10 Rev P Tyco Electronics Corporation 7.2. Periodic Inspection Regular inspections should be performed by quality control personnel. A record of scheduled inspections should remain with the tool and/or be supplied to supervisory personnel responsible for the tool. Though recommendations call for at least one inspection per month, the inspection frequency should be based on the amount of use, working conditions, operator training and skill, and established company standards. These inspections should be performed in the following sequence: A. Visual Inspection 1. Remove all lubrication and accumulated film by immersing the tool (handles partially closed) in a suitable commercial degreaser that will not affect paint or plastic material. 2. Make certain that all retaining pins are in place and are secured with retaining rings. If replacements are necessary, refer to the parts list in Figure 11. 3. Inspect crimping areas for pitted or chipped surfaces. 4. Close the tool handles until the ratchet releases, then allow handles to open freely. If they do not open quickly and fully, the spring is defective and must be replaced. Refer to Section 8, REPLACEMENT AND REPAIR. B. Gaging the Crimping Areas This inspection requires the use of plug gages conforming to the dimensions listed in Figures 8 and 9. Tyco Electronics does not manufacture or market these gages. To gage the crimping area(s), refer to Figure 10 and proceed as follows: 1. Close the crimping areas by squeezing the tool handles together until the crimping dies have bottomed, and then HOLD the tool handles in this position. Do not force the dies beyond initial contact. Figure 8 TOOL NUMBER DIE CLOSURE DIM'S. A"{ GAGE ELEMENT{{ DIM'S. B" DIA. GO NO-GO GO NO-GO C" MAX. R" RADIUS 46121 169485 1.600 [.0630] 1.753 [.0690] 1.600-1.608 [.0630-.0633] 1.750-1.753 [.0689-.0690] 47304 1.600 [.0630] 1.753 [.0690] 1.600-1.608 [.0630-.0633] 1.750-1.753 [.0689-.0690] 47386 47386-5 2.768 [.1090] 2.921 [.1150] 2.768-2.776 [.1090-.1093] 2.918-2.921 [.1149-.1150] 47387 3.022 [.1190] 3.175 [.1250] 3.022-3.030 [.1190-.1193] 3.172-3.175 [.1249-.1250] 47907-1 2.260 [.0890] 2.413 [.0950] 2.260-2.268 [.0890-.0893] 2.410-2.413 [.0949-.0950] 48518-2 1.600 [.0630] 1.753 [.0690] 1.600-1.608 [.0630-.0633] 1.750-1.753 [.0689-.0690] 69151-1 2.768 [.1090] 2.921 [.1150] 2.768-2.776 [.1090-.1093] 2.918-2.921 [.1149-.1150] 69454 2.616 [.1030] 2.718 [.1070] 2.616-2.624 [.1030-.1033] 2.715-2.718 [.1069-.1070] 3.962 [.156] 3.454 [.136] { Die closure dimensions apply when wire barrel jaws are bottomed, but not under pressure. {{ MaterialTool Steel. SUGGESTED PLUG GAGE DESIGN WIRE BARREL CRIMP NO-GO Dim. B" A" Dim. 12.7 [.50] Min. Typ. R" Typ. 31.75 [.125] Min. Typ. C" R" Typ. GO Dim. B" Tool No. 69454 Only Die Closure Configuration NO-GO Dim. A" DIM. GO Dim. Die Closure Configuration B" Dia. 50.8 [2.00] Min. Typ. B" Dia. |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |