Electronic Components Datasheet Search
  English  ▼

X  

46121 Datasheet(PDF) 8 Page - Tyco Electronics

Part # 46121
Description  Hand Crimping Tools
PDF  10 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  MACOM [Tyco Electronics]
Direct Link  http://www.macom.com
Logo MACOM - Tyco Electronics

46121 Datasheet(HTML) 8 Page - Tyco Electronics

Back Button 46121 Datasheet HTML 2Page - Tyco Electronics 46121 Datasheet HTML 3Page - Tyco Electronics 46121 Datasheet HTML 4Page - Tyco Electronics 46121 Datasheet HTML 5Page - Tyco Electronics 46121 Datasheet HTML 6Page - Tyco Electronics 46121 Datasheet HTML 7Page - Tyco Electronics 46121 Datasheet HTML 8Page - Tyco Electronics 46121 Datasheet HTML 9Page - Tyco Electronics 46121 Datasheet HTML 10Page - Tyco Electronics  
Zoom Inzoom in Zoom Outzoom out
 8 / 10 page
background image
408-1559
Hand Crimping Tools
Rev P
8 of 10
Tyco Electronics Corporation
Figure 9
TOOL NUMBER
DIE CLOSURE DIM'S. F"{ (Set Insulation
Adjustment Pins at No. 1 Position)
GAGE ELEMENT {{ DIM'S. G"
GO
NO-GO
GO
NO-GO
WIDTH
W" (Max.)
46121
169485
0.762
[.0300]
1.27
[.0500]
0.762-0.77
[.0300-.0303]
1.267-1.27
[.0499-.0500]
47304
47387
1.016
[.0400]
1.524
[.0600]
1.016-1.024
[.0400-.0403]
1.521-1.524
[.0599-.0600]
47907-1
48518-2
69151-1
69454
{ Die closure dimensions apply when wire barrel jaws are bottomed, but not under pressure.
{{ MaterialTool Steel.
SUGGESTED PLUG GAGE DESIGN INSULATION CRIMP
GO Dim.
NO-GO Dim.
G"
G"
W"
GO
NO
GO
6.35 [.250] Typ.
F" Dim.
Die Closure
Configuration
3.18
[.125]
4.75
[.187]
0.762
[.0300]
1.27
[.0500]
0.762-0.77
[.0300-.0303]
1.267-1.27
[.0499-.0500]
3.18
[.125]
0.762
[.0300]
1.27
[.0500]
0.762-0.77
[.0300-.0303]
1.267-1.27
[.0499-.0500]
3.18
[.125]
0.762
[.0300]
1.27
[.0500]
0.762-0.77
[.0300-.0303]
1.267-1.27
[.0499-.0500]
2.36
[.093]
0.762
[.0300]
1.27
[.0500]
0.762-0.77
[.0300-.0303]
1.267-1.27
[.0499-.0500]
3.18
[.125]
0.762
[.0300]
1.27
[.0500]
0.762-0.77
[.0300-.0303]
1.267-1.27
[.0499-.0500]
3.18
[.125]
0.762
[.0300]
1.27
[.0500]
0.762-0.77
[.0300-.0303]
1.267-1.27
[.0499-.0500]
3.18
[.125]
47386
47386-5
2. Align the GO element of the gage with the
appropriate crimping area to be checked. Refer to
Figure 10. Push the element straight into the area
without using force. The GO element must pass
completely through the crimping area.
3. Align the NO–GO element of the gage with the
same crimping area, and try to insert the element.
The NO–GO element may start entry, but it must
not pass completely through the crimping area.
4. Repeat the gage inspection procedure for each
crimping area, making sure to use the correct plug
gage for each inspection.
If the crimping areas conform to the gage inspection,
the tool is considered dimensionally correct. If the
crimping areas do not conform to the inspection, the
tool must be repaired. Refer to Section 8,
REPLACEMENT AND REPAIR.
For additional information concerning the use of the
plug gage, refer to instruction sheet 408–7424.
C. CERTI-CRIMP Hand Crimping Tool Ratchet
Control Inspection
Obtain a .025–mm [.001–in.] shim that is suitable for
checking the clearance between the bottoming
surfaces of the crimping dies. To inspect the ratchet
control:
1. Refer to Figure 3 and select a terminal or splice
and wire (maximum size).
2. Position the terminal or splice in the appropriate
crimping area, according to the method described
in Paragraph 3.1, Steps 1 through 5.
3. While holding the wire in place, squeeze the tool
handles together until the ratchet releases. Hold
the tool in this position, maintaining just enough
pressure to keep the dies closed.



Html Pages

1 2 3 4 5 6 7 8 9 10


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com