A3P030 datasheet(213/220 Pages) MICROSEMI

213 / 220 page

ProASIC3 Flash Family FPGAs

Revision 13

5-7

v2.0

(April 2007)

In the "Packaging Tables", Ambient was deleted.

The timing characteristics tables were updated.

N/A

The "PLL Macro" section was updated to add information on the VCO and PLL

outputs during power-up.

2-15

The "PLL Macro" section was updated to include power-up information.

2-15

Table 2-11 • ProASIC3 CCC/PLL Specification was updated.

2-29

Figure 2-19 • Peak-to-Peak Jitter Definition is new.

2-18

The "SRAM and FIFO" section was updated with operation and timing

requirement information.

2-21

The "RESET" section was updated with read and write information.

2-25

The "RESET" section was updated with read and write information.

2-25

The "Introduction" in the "Advanced I/Os" section was updated to include

information on input and output buffers being disabled.

2-28

PCI-X 3.3 V was added to Table 2-11 • VCCI Voltages and Compatible

Standards.

2-29

In the Table 2-15 • Levels of Hot-Swap Support, the ProASIC3 compliance

descriptions were updated for levels 3 and 4.

2-34

Table 2-43 • I/O Hot-Swap and 5 V Input Tolerance Capabilities in ProASIC3

Devices was updated.

2-64

Notes 3, 4, and 5 were added to Table 2-17 • Comparison Table for 5 V–

Compliant Receiver Scheme. 5 x 52.72 was changed to 52.7 and the Maximum

current was updated from 4 x 52.7 to 5 x 52.7.

2-40

The "VCCPLF PLL Supply Voltage" section was updated.

2-50

The "VPUMP Programming Supply Voltage" section was updated.

2-50

The "GL Globals" section was updated to include information about direct input

into quadrant clocks.

2-51

VJTAG was deleted from the "TCK Test Clock" section.

2-51

In Table 2-22 • Recommended Tie-Off Values for the TCK and TRST Pins, TSK

was changed to TCK in note 2. Note 3 was also updated.

2-51

Ambient was deleted from Table 3-2 • Recommended Operating Conditions.

VPUMP programming mode was changed from "3.0 to 3.6" to "3.15 to 3.45".

3-2

Note 3 is new in Table 3-4 • Overshoot and Undershoot Limits (as measured on

quiet I/Os)1.

3-2

In EQ 3-2, 150 was changed to 110 and the result changed from 3.9 to 1.951.

3-5

Table 3-6 • Temperature and Voltage Derating Factors for Timing Delays was

updated.

3-6

Table 3-5 • Package Thermal Resistivities was updated.

3-5

Table 3-14 • Summary of Maximum and Minimum DC Input and Output Levels

Applicable to Commercial and Industrial Conditions—Software Default Settings

(Advanced) and Table 3-17 • Summary of Maximum and Minimum DC Input

Levels Applicable to Commercial and Industrial Conditions (Standard Plus) were

updated.

3-17 to 3-

Revision

Changes

Page

A3P030 Datasheet(PDF) 213 Page - Microsemi Corporation

A3P030 Datasheet(HTML) 213 Page - Microsemi Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL