| Electronic Components Datasheet Search |
|
CS5101A Datasheet(PDF) 26 Page - Cirrus Logic |
|
|
|||||||||||||||||||||||||||||
CS5101A Datasheet(HTML) 26 Page - Cirrus Logic |
|
26 / 40 page ![]() captured and processed. The FFT algorithm ana- lyzes the spectral content of the digital waveform and distributes its energy among 512 "frequency bins." Assuming an ideal sinewave, distribution of energy in bins outside of the fundamental and dc can only be due to quantization effects and errors in the CS5101A and CS5102A. If sampling is not synchronized to the input sine- wave, it is highly unlikely that the time record will contain an integer number of periods of the input signal. However, the FFT assumes that the signal is periodic, and will calculate the spectrum of a signal that appears to have large discontinui- ties, thereby yielding a severely distorted spectrum. To avoid this problem, the time record is multiplied by a window function prior to per- forming the FFT. The window function smoothly forces the endpoints of the time record to zero, thereby removing the discontinuities. The effect of the window in the frequency-domain is to con- volute the spectrum of the window with that of the actual input. The quality of the window used for harmonic analysis is typically judged by its highest side- lobe level. A five term window is used in FFT testing of the CS5101A and CS5102A. This win- dowing algorithm attenuates the side-lobes to below the noise floor. Artifacts of windowing are discarded from the signal-to-noise calculation us- ing the assumption that quantization noise is white. Averaging the FFT results from ten time records filters the spectral variability that can arise from capturing finite time records without disturbing the total energy outside the fundamen- tal. All harmonics are visible in the plots. For more information on FFT’s and windowing refer to: F.J. HARRIS, "On the use of windows for harmonic analysis with the Discrete Fourier Transform", Proc. IEEE, Vol. 66, No. 1, Jan 1978, pp.51-83. This is available on request from Crystal Semiconductor. As illustrated in Figure 17, the CS5101A typi- cally provides about 92 dB S/(N+D) and 0.001% THD at 25 °C. Figure 18 illustrates only minor degradation in performance when the am- bient temperature is raised to 138 °C. Figure 19 and 20 illustrate that the CS5102A typically yields >92 dB S/(N+D) and 0.001% THD even with a large change in ambient temperature. Un- like conventional successive-approximation ADC’s, the signal-to-noise and dynamic range of the CS5101A and CS5102A are not limited by differential nonlinearities (DNL) caused by cali- bration errors. Rather, the dominant noise source is broadband thermal noise which aliases into the baseband. This white broadband noise also ap- pears as an idle channel noise of 1/2 LSB (rms). Sampling Distortion Like most discrete sample/hold amplifier designs, the inherent sample/hold of the CS5101A and CS5102A exhibits a frequency-dependent distor- tion due to nonideal sampling of the analog input voltage. The calibrated capacitor array used dur- ing conversions is also used to track and hold the analog input signal. The conversion is not per- formed on the analog input voltage per se, but is actually performed on the charge trapped on the capacitor array at the moment the HOLD com- mand is given. The charge on the array ideally assumes a linear relationship to the analog input voltage. Any deviation from this linear relation- ship will result in conversion errors even if the conversion process proceeds flawlessly. At dc, the DAC capacitor array’s voltage coeffi- cient dictates the converter’s linearity. This variation in capacitance with respect to applied signal voltage yields a nonlinear relationship be- tween the charge on the array and the analog input voltage and places a bow or wave in the transfer function. This is the dominant source of d istortion at lo w in pu t freq uencies (Fig- ures 17,18,19, and 20). The ideal relationship between the charge on the array and the input voltage can also be distorted CS5101A CS5102A 26 DS45F2 |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |