LTC1326CS8 datasheet(8/16 Pages) LINER

8 / 16 page

LTC1326/LTC1326-2.5

The three internal precision voltage comparators have

response times that are typically 13

µs. This slow re-

sponse time helps prevent mistriggering due to tran-

sients on each of the VCC inputs. The part’s ability to

suppress transients can be improved by bypassing each

of the VCC inputs with a 0.1µF capacitor to ground.

Push-Button Reset

The parts provide a push-button reset input pin. The PBR

input has an internal pull-up current source to VCC3. If the

PBR pin is not used it can be left floating.

When the PBR is pulled low for less than tPB (≈ 2 sec), a

narrow (100

µs typ) soft reset pulse is generated on the

SRST output pin after the button is released. The push-

button circuitry contains an internal debounce counter

which delays the output of the soft reset pulse by typically

20ms. This pin can be OR-tied to the RST pin and issue

what is called a “soft” reset. The SRST thereby resets the

microprocessor without interrupting the DRAM refresh

cycle. In this manner DRAM information remains undis-

turbed. Alternatively, SRST may be monitored by the

processor to initiate a software-controlled reset.

When the PBR pin is held low for longer than tPB (≈ 2 sec),

a standard reset is generated on the RST and RST pins.

Once the 2 second period has elapsed, a reset signal is

produced by the push-button logic, thereby clearing the

reset counter. Once the button is released, the reset

counter begins counting the reset period (200ms nomi-

nal). Consequently, the reset outputs remain asserted for

approximately 200ms after the button is released.

TI I G DIAGRA S

APPLICATIO S I FOR ATIO

Operation

The LTC1326/LTC1326-2.5 are micropower, high accu-

racy triple supply monitoring circuits. The parts have two

basic functions: generation of a reset when power sup-

plies are out of range, and generation of reset or a “soft”

reset when the PBR pin is pulled low.

Supply Monitoring

All three VCC inputs must be above predetermined

thresholds for 200ms before the reset output is released.

The parts will assert reset during power-up, power-down

and brownout conditions on any one or more of the VCC

inputs.

On power-up, either the VCC5 or VCC3 pin on the LTC1326,

or the VCC25 or VCC3 pin on the LTC1326-2.5, can power

the drive circuits for the RST pin. This ensures that RST

will be low when VCC5, VCC25 or VCC3 reaches 1V. As long

as any one of the VCC inputs is below its predetermined

threshold, RST will stay a logic low. Once all of the VCC

inputs rise above their thresholds, an internal timer is

started and RST is released after 200ms. The RST pin

outputs the inverted state of what is seen on RST pin.

RST is reasserted whenever any one of the VCC inputs

drops below its predetermined threshold and remains

asserted until 200ms after all of the VCC inputs are above

their thresholds.

On power-down, once any of the VCC inputs drop below

its threshold, RST is held at a logic low. A logic low of 0.4V

is guaranteed until VCC3 and VCC5 on the LTC1326 or VCC3

and VCC25 on the LTC1326-2.5 drop below 1V.

Push-Button Reset Function Timing

t < tPB

tPB

tRST

tDB

tSRST

1326/2.5 TD02

PBR

RST

SRST

tRST

1326/2.5 TD01

VRTX

VCCX

RST

VCC Monitor Timing

LTC1326CS8 Datasheet(PDF) 8 Page - Linear Technology

LTC1326CS8 Datasheet(HTML) 8 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Datasheet Download

Link URL