| Electronic Components Datasheet Search |
|
MAX863 Datasheet(PDF) 7 Page - Maxim Integrated Products |
|
|
|||||||||||||||||||||||||||||
MAX863 Datasheet(HTML) 7 Page - Maxim Integrated Products |
|
7 / 16 page ![]() Dual, High-Efficiency, PFM, Step-Up DC-DC Controller _______________________________________________________________________________________ 7 Continuous/Discontinuous-Conduction Modes Each converter in the MAX863 determines from moment to moment whether to switch or not, waiting until the out- put voltage drops before initiating another cycle. Under light loads, the inductor current ramps to zero before the next cycle; this is discontinuous-conduction mode. Continuous-conduction mode occurs when the next switching cycle begins while current is still flowing through the inductor. The transition point between dis- continuous- and continuous-conduction mode is deter- mined by input and output voltages, and by the size of the inductor relative to the peak switching current. In general, reducing inductance toward the minimum rec- ommended value pushes the transition point closer to the maximum load current. If the inductor value is low enough or the output/input voltage ratio high enough, the DC-DC converter may remain in discontinuous-con- duction mode throughout its entire load range. The MAX863 transitions into continuous-conduction mode in two ways, depending on whether preset or adjustable mode is used and how the external feed- back network is compensated. Under light loads, the IC switches in single pulses (Figure 3a). The threshold of transition into continuous-conduction mode is reached when the inductor current waveforms are adjacent to one another, as shown in Figure 3b. As the load increases, the transition into continuous-conduction mode progresses by raising the minimum inductor cur- rent (Figures 3c, 3d). Depending on feedback compen- sation, transition into continuous-conduction mode may also progress with grouped pulses (Figures 3e, 3f). Pulse groups should be separated by less than two or three switching cycles. Output ripple should not be significantly more than the single-cycle no-load case. MAX863 EXT2 CS2 VOUT2 = 3.3V VOUT1 = 5V VIN = 1.5V TO THE LOWER OF VOUT1 OR VOUT2 N1B IRF7301 C7 0.1 µF R4 100k 1% C6 10pF C5 330 µF 10V ≤0.1Ω R2 50m Ω R3 165k 1% N1A R1 50m Ω R7 100k C1 220 µF 10V ≤0.1Ω R5 R6 C2 0.1 µF D1 MBRS340T3 D2 MBRS340T3 L1 10 µH 2A L2 10 µH 2A C3 100 µF 10V ≤0.1Ω C4 100 µF 10V ≤0.1Ω ON/OFF FB2 SHDN1 EXT1 CS1 LBO LOW-BATTERY DETECTOR OUTPUT LBI SENSE1 VDD PGND BOOT GND FB1 SHDN2 REF Figure 2. Bootstrapped Typical Operating Circuit |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |