MIC58P01 datasheet(3/5 Pages) MICREL

3 / 5 page

October 1998

7-19

MIC58P01

Micrel

Electrical Characteristics: at TA = +25°C, VDD = 5V (unless otherwise noted)

Limits

Characteristic

Symbol

Test Conditions

Min.

Typ.

Max.

Units

Output Leakage Current

ICEX

VCE = 80V, TA = +25°C50

µA

VCE = 80V, TA = +70°C

100

Collector-Emitter

VCE(SAT)

IC = 100mA

0.9

1.1

Saturation Voltage

IC = 200mA

1.1

1.3

IC = 350mA

1.3

1.6

Input Voltage

VIN(0)

1.0

VIN(1)

VDD = 12V

10.5

VDD = 10V

8.5

VDD = 5.0V (See Note)

3.5

Input Resistance

RIN

VDD = 12V

200

Ω

VDD = 10V

300

VDD = 5.0V

600

Supply Current

IDD(ON)

VDD = 12V, Outputs Open

3.3

4.5

(One output

VDD = 10V, Outputs Open

3.1

4.5

active)

VDD = 5.0V, Outputs Open

2.4

3.6

IDD(ON)

VDD = 12V, Outputs Open

6.4

10.0

(All outputs

VDD = 10V, Outputs Open

6.0

9.0

active)

VDD = 5.0V, Outputs Open

4.7

7.5

IDD(OFF)

VDD = 12V, Outputs Open, Inputs = 0V

3.0

4.5

(Total)

VDD = 5.0V, Outputs Open, Inputs = 0V

2.2

3.6

Clamp Diode

VR = 80V, TA = +25°C50

µA

Leakage Current

VR = 80V, TA = +70°C

100

Overcurrent Threshold

ILIM

Per Output

500

Start-Up Voltage

VSU

Note 2.

3.5

4.0

4.5

Minimum Operating VDD

VDD MIN

3.0

3.5

4.0

Clamp Diode Forward Voltage

IF = 350mA

1.7

2.0

Thermal Shutdown

165

°C

Thermal Shutdown Hystersis

°C

NOTE 1:

Operation of these devices with standard TTL or DTL may require the use of appropriate pull-up resistors to insure a minimum logic “1”.

NOTE 2:

Under-Voltage Lockout is guaranteed to release device at no more than 4.5V, and disable the device at no less than 3.0V.

Truth Table

Output

OUTN

INN

Strobe

Clear

Enable

t–1

OFF

X = Irrelevant

t–1 = previous output state

t = present output state

Information present at an input is transferred to its latch when

the STROBE is high. A high CLEAR input will set all latches

to the output OFF condition regardless of the Data or STROBE

input levels. A high OUTPUT ENABLE will set all outputs to

the OFF condition, regardless of any other input conditions.

When the OUTPUT ENABLE is low, the outputs depend on

the state of their respective latches. If current shutdown is

activated, the OUTPUT ENABLE must be pulsed high to

restore operation. Over temperature faults are not latched

and require no reset pulse.

MIC58P01 Datasheet(PDF) 3 Page - Micrel Semiconductor

MIC58P01 Datasheet(HTML) 3 Page - Micrel Semiconductor

Html Pages

1 2 3 4 5

Datasheet Download

Link URL