Electronic Components Datasheet Search
  English  ▼

X  

FM3808 Datasheet(PDF) 13 Page - Ramtron International Corporation

Part # FM3808
Description  256Kb Bytewide FRAM w/ Real-Time Clock
PDF  28 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  RAMTRON [Ramtron International Corporation]
Direct Link  http://www.ramtron.com
Logo RAMTRON - Ramtron International Corporation

FM3808 Datasheet(HTML) 13 Page - Ramtron International Corporation

Back Button FM3808 Datasheet HTML 9Page - Ramtron International Corporation FM3808 Datasheet HTML 10Page - Ramtron International Corporation FM3808 Datasheet HTML 11Page - Ramtron International Corporation FM3808 Datasheet HTML 12Page - Ramtron International Corporation FM3808 Datasheet HTML 13Page - Ramtron International Corporation FM3808 Datasheet HTML 14Page - Ramtron International Corporation FM3808 Datasheet HTML 15Page - Ramtron International Corporation FM3808 Datasheet HTML 16Page - Ramtron International Corporation FM3808 Datasheet HTML 17Page - Ramtron International Corporation Next Button
Zoom Inzoom in Zoom Outzoom out
 13 / 28 page
background image
FM3808
Rev 1.1
May 2003
Page 13 of 28
Interrupts
The supervisor was designed to serve diverse
applications. Its sophistication and programmability
make the supervisor function highly configurable for
the host system. The interrupt block is capable of
providing system interrupt or reset conditions, and
can even power up a system at a preprogrammed
time. Although the INT pin is described as an
interrupt, the pin may be used as a reset source as
well.
The supervisor provides three potential interrupt
sources. They include the watchdog timer, the power
monitor, and the clock/calendar alarm. Each can be
individually enabled and assigned to drive the INT
pin. In addition, each has an associated flag bit that
the host processor can use to determine the cause of
the interrupt.
Some of the sources have additional control bits that
determine functional behavior. In addition, the pin
driver has three bits that specify its behavior when an
interrupt occurs. A functional diagram of the interrupt
logic is shown below.
The three interrupts each have a source and an
enable. Both the source and the enable must be active
(true high) in order to generate an interrupt output.
Only one source is necessary to drive the pin. The
user
can
identify
the
source
by
reading
the
Flags/Control register, which contains the flags
associated with each source. All flags are cleared to 0
when the register is read. The cycle must be a
complete read cycle (/WE high), otherwise the flags
will not be cleared. The power monitor has two
programmable settings that are explained above in the
power monitor section.
Once an interrupt source is active, the pin driver
determines the behavior of the output. It has two
programmable settings as shown below. Pin driver
control bits are located in the Interrupts register
7FF6h bits D3-D2.
Watchdog
Timer
WDF
WIE
Power
Monitor
PF
PFE
VINT
Clock
Alarm
AF
AIE
Pin
Driver
ABE
P/L
H/L
VDD
INT
Figure 5. Interrupt Block Diagram
According to the programming selections, the pin can
be driven in the backup mode for an alarm interrupt.
In addition, the pin can be an active low (open-drain)
or active high (push-pull) driver. If programmed for
operation during backup mode, it can only be active
low. Lastly, the pin can provide a one-shot function
so that the active condition is a pulse, or a level
condition. In One-Shot mode, the pulse width is
internally fixed at approximately 200 ms. This mode
is intended to reset a host microcontroller. In Level
mode, the pin goes to its active polarity until the
Flags/Control register is read by the user. This mode
is intended to be used as an interrupt to a host
microcontroller. The control bits are summarized as
follows.
Watchdog Interrupt Enable - WIE. When set to 1, the
watchdog timer drives the INT pin as well as an
internal flag when a watchdog timeout occurs. When



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com