USE ULTRA37000™ FOR
ALL NEW DESIGNS
CY7C343
Document #: 38-03015 Rev. *B
Page 5 of 19
Maximum Ratings
(Above which the useful life may be impaired. For user guide-
lines, not tested.)
Storage Temperature ................................ –65
°C to +150°C
Ambient Temperature with
Power Applied.................................................. 0
°C to +70°C
Maximum Junction Temperature
(Under Bias)................................................................. 150
°C
Supply Voltage to Ground Potential ............... –2.0V to +7.0V
Maximum Power Dissipation...................................2500 mW
DC VCC or GND Current ............................................500 mA
DC Output Current, per Pin ......................–25 mA to +25 mA
DC Input Voltage[1] .........................................–3.0V to +7.0V
DC Program Voltage..................................................... 13.0V
Static Discharge Voltage........................................... > 1100V
(per MIL–STD–883, method 3015)
Notes:
1. Minimum DC input is –0.3V. During transitions, the inputs may undershoot to –2.0V for periods less than 20 ns.
2. The Voltage on any input or I/O pin cannot exceed the power pin during power-up.
3. Typical values are for TA = 25°C and VCC = 5V.
4. Not more than one output should be tested at a time. Duration of the short circuit should not be more than one second. VOUT = 0.5V has been chosen to avoid
test problems caused by tester ground degradation.
5. Guaranteed but not 100% tested.
6. Measured with device programmed as a 16-bit counter in each LAB. This parameter is tested periodically by sampling production material.
7. Part (a) in AC Test Load and Waveforms is used for all parameters except tER and tXZ, which is used for part (b) in AC Test Load and Waveforms. All external
timing parameters are measured referenced to external pins of the device.
Operating Range[2]
Range
Ambient Temperature
VCC
Commercial
0
°C to +70°C
5V
±5%
Industrial
–40
°C to +85°C
5V
±10%
Military
–55
°C to +125°C (Case)
5V
±10%
Electrical Characteristics Over the Operating Range[3]
Parameter
Description
Test Conditions
Min.
Max.
Unit
VOH
Output HIGH Voltage
VCC = Min., IOH = –4.0 mA
2.4
V
VOL
Output LOW Voltage
VCC = Min., IOL = 8 mA
0.45
V
VIH
Input HIGH Level
2.2
VCC + 0.3
V
VIL
Input LOW Level
–0.3
0.8
V
IIX
Input Current
GND < VIN < VCC
–10
+10
µA
IOZ
Output Leakage Current
VO = VCC or GND
–40
+40
µA
IOS
Output Short Circuit Current
VCC = Max., VOUT = 0.5V
[4, 5]
–30
–90
mA
ICC1
Power Supply Current (Standby)
VI = VCC or GND
(No Load)
Commercial
125
mA
Military/Industrial
200
mA
ICC2
Power Supply Current[6]
VI = VCC or GND (No
Load) f = 1.0 MHz[5, 6]
Commercial
135
mA
Military/Industrial
225
mA
tR
Recommended Input Rise Time
100
ns
tF
Recommended Input Fall Time
100
ns
Capacitance[7]
Parameter
Description
Test Conditions
Max.
Unit
CIN
Input Capacitance
VIN = 2V, f = 1.0 MHz
10
pF
COUT
Output Capacitance
VOUT = 2.0V, f = 1.0 MHz
10
pF
AC Test Loads and Waveforms[7]
3.0V
5V
OUTPUT
R1 464
Ω
R2
250
Ω
50 pF
INCLUDING
JIG AND
SCOPE
GND
90%
10%
90%
10%
<6 ns
<6 ns
5V
OUTPUT
R1 464
Ω
R2
250
Ω
5pF
INCLUDING
JIG AND
SCOPE
(a)
(b)
OUTPUT
1.75V
Equivalent to:
THÉVENIN EQUIVALENT (commercial/military)
ALL INPUT PULSES
163
Ω
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
