| Electronic Components Datasheet Search |
|
IR2156SPBF Datasheet(PDF) 19 Page - International Rectifier |
|
|
|||||||||||||||||||||||||||||
IR2156SPBF Datasheet(HTML) 19 Page - International Rectifier |
|
19 / 24 page ![]() IR2156(S)&(PbF) www.irf.com 19 Design Equations Note: The results from the following design equations can differ slightly from experimental measurements due to IC tolerances, component tolerances, and oscillator over- and under-shoot due to internal comparator response time. Step 1: Program Dead-time The dead-time between the gate driver outputs HO and LO is programmed with timing capacitor CT and an internal dead-time resistor RDT. The dead-time is the discharge time of capacitor CT from 3/5VCC to 1/3VCC and is given as: 2000 ⋅ = T DT C t [Seconds] (1) or 2000 DT T t C = [Farads] (2) Step 2: Program Run Frequency The final run frequency is programmed with timing resistor RT and timing capacitor CT. The charge time of capacitor CT from 1/3VCC to 3/5VCC determines the on-time of HO and LO gate driver outputs. The run frequency is therefore given as: ) 2000 6 . 0 ( 2 1 + ⋅ ⋅ = T T RUN R C f [Hertz] (3) or 3333 12 . 1 1 − ⋅ ⋅ = RUN T T f C R [Ohms] (4) Step 3: Program Preheat Frequency The preheat frequency is programmed with timing resistors RT and RPH, and timing capacitor CT. The timing resistors are connected in parallel internally for the duration of the preheat time. The preheat frequency is therefore given as: + + ⋅ ⋅ ⋅ ⋅ = 2000 6 . 0 2 1 PH T PH T T PH R R R R C f [Hertz] (5) or − ⋅ ⋅ − ⋅ − ⋅ ⋅ = 3333 12 . 1 1 3333 12 . 1 1 PH T T T PH T PH f C R R f C R [Ohms] (6) Step 4: Program Preheat Time The preheat time is defined by the time it takes for the capacitor on pin CPH to charge up to 13 volts (assuming Vcc = 15 volts). An internal current source of 4.3 µA flows out of pin CPH. The preheat time is therefore given as: [Seconds] (7) or [Farads] (8) Step 5: Program Maximum Ignition Current The maximum ignition current is programmed with the external resistor RCS and an internal threshold of 1.25 volts. This threshold determines the over- current limit of the ballast, which can be exceeded when the frequency ramps down towards resonance during ignition and the lamp does not 6 02 . 3 e C t PH PH ⋅ = 6 331 . 0 − ⋅ = e t C PH PH |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |