Electronic Components Datasheet Search
  English  ▼

X  

LMX2216 Datasheet(PDF) 9 Page - National Semiconductor (TI)

[Old version datasheet] Texas Instruments acquired National semiconductor.
Part # LMX2216
Description  0.1 GHz to 2.0 GHz Low Noise Amplifier/Mixer for RF Personal Communications
PDF  12 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  NSC [National Semiconductor (TI)]
Direct Link  http://www.national.com
Logo NSC - National Semiconductor (TI)

LMX2216 Datasheet(HTML) 9 Page - National Semiconductor (TI)

Back Button LMX2216 Datasheet HTML 4Page - National Semiconductor (TI) LMX2216 Datasheet HTML 5Page - National Semiconductor (TI) LMX2216 Datasheet HTML 6Page - National Semiconductor (TI) LMX2216 Datasheet HTML 7Page - National Semiconductor (TI) LMX2216 Datasheet HTML 8Page - National Semiconductor (TI) LMX2216 Datasheet HTML 9Page - National Semiconductor (TI) LMX2216 Datasheet HTML 10Page - National Semiconductor (TI) LMX2216 Datasheet HTML 11Page - National Semiconductor (TI) LMX2216 Datasheet HTML 12Page - National Semiconductor (TI)  
Zoom Inzoom in Zoom Outzoom out
 9 / 12 page
background image
Functional Description (Continued)
THE LNA
The LNA is a common emitter stage with active feedback
This feedback network allows for wide bandwidth operation
while providing the necessary optimal input impedance for
low noise performance The power down feature is imple-
mented using a CMOS buffer and a power-down switch The
power down switch is implemented with CMOS devices
During power down the switch is open and only leakage
currents are drawn from the supply
THE MIXER
The mixer is a Gilbert cell architecture with the RF input
signal modulating the LO signal and single ended output
taken from the collector of one of the upper four transistors
The power down circuitry of the mixer is similar to that of the
LNA The power down switch is used to provide or cut off
bias to the Gilbert cell
Typical Low Noise Amplifier
TLW11814 – 14
FIGURE 4 Typical LNA Structure
A typical low noise amplifier consists of an active amplifying
element and input and output matching networks The input
matching network is usually optimized for noise perform-
ance and the output matching network for gain The active
element is chosen such that it has the lowest optimal noise
figure FMIN an intrinsic property of the device The noise
figure of a linear two-port is a function of the source admit-
tance and can be expressed by
F e FMIN a
Rn
GG
(GON b GG)2 a (BON b BG)2
where GG a jBG
e
generator admittance presented to
the input of the two port
GON a jBON e generator admittance at which op-
timum noise figure occurs
Rn
e
empirical
constant
relating
the
sensitivity of the noise figure to
generator admittance
Typical Gilbert Cell
TLW11814 – 15
FIGURE 5 Typical Gilbert Cell Circuit Diagram
The Gilbert cell shown above is a circuit which multiplies
two input signals RF and LO The input RF voltage differen-
tially modulates the currents on the collectors of the transis-
tors Q1 and Q2 which in turn modulate the LO voltage by
varying the bias currents of the transistors Q3 Q4 Q5 and
Q6 Assuming that the two signals are small the result is a
product of the two signals producing at the output a sum
and difference of the frequencies of the two input signals If
either of these two signals are much larger than the thresh-
old voltage VT the output will contain other mixing products
and higher order terms which are undesirable and may need
to be attenuated or filtered out
Analysis of the Gilbert cell shows that the output which is
the difference of the collector currents of Q3 and Q6 is
related to the two inputs by the equation
D
I e IC3 b IC6 e IEE tanh
VRF
2VT
J( tanh VLO
2VT
J(
and the hyperbolic tangent function can be expressed as a
Taylor series
tanh(x) e x b
x3
3
a
x5
5
b
Assuming that the RF and LO signals are sinusoids
VRF e Acos (0RF t a wRF)
VLO e Bcos (0LO t a wLO)
then
D
I e IEE Acos (0RF t a wRF) b
A3
3
cos3 (0RF t a wRF )a
(
 Bcos (0LO t a wLO) b
B3
3
cos3 (0LO t a wLO) a
(
The lowest order term is a product of two sinusoids yielding
a sum of two sinusoids
IEE
AB
2
cos ((0RF a 0LO)t a wRF awLO)
a
cos ((0RF b 0LO)t a wRF b wLO)
(
one of which is the desired intermediate frequency signal
9



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com