ST7DALIF2 datasheet(132/171 Pages) STMICROELECTRONICS

132 / 171 page

Electrical characteristics

ST7DALIF2

132/171

The RC oscillator and PLL characteristics are temperature-dependent and are grouped in

four tables.

Table 68.

Operating voltage and startup time

Symbol

Parameter

Min

Typ

Max

Unit

VDD(RC)

Internal RC Oscillator operating voltage

2.4

5.5

VDD(x4PLL)

x4 PLL operating voltage

2.4

3.3

VDD(x8PLL)

x8 PLL operating voltage

3.3

5.5

tSTARTUP

PLL Startup time

PLL

input

clock

(fPLL)

cycles

Table 69.

RC oscillator and PLL characteristics (tested for TA = -40 to +85° C) @ VDD = 4.5 to

5.5 V

Symbol

Parameter

Conditions

Min

Typ

Max

Unit

fRC

Internal RC oscillator

frequency (1)

RCCR = FF (reset value), TA=25° C,

VDD=5 V

760

kHz

RCCR = RCCR0(2), TA=25° C, VDD=5 V

1000

ACCRC

Accuracy of Internal RC

oscillator with

RCCR=RCCR0(2)

TA=25° C, VDD=4.5 to 5.5 V

-1

+1%

TA=-40 to +85° C, VDD=5 V

-5

TA=0 to +85° C, VDD=4.5 to 5.5 V

-2(3)

+2(3)

IDD(RC)

RC oscillator current

consumption

TA=25° C, VDD=5 V

970(3)

μA

tsu(RC)

RC oscillator setup time

TA=25° C, VDD=5 V

10(2)

μs

fPLL

x8 PLL input clock

1(3)

MHz

tLOCK

PLL Lock time(4)

2ms

tSTAB

PLL Stabilization time(4)

4ms

ACCPLL

x8 PLL Accuracy

fRC = 1 MHz@TA=25° C, VDD=4.5 to 5.5 V

0.1(5)

fRC = 1 MHz@TA=-40 to +85° C, VDD=5 V

0.1(5)

tw(JIT)

PLL jitter period

fRC = 1 MHz

125(6)

µs

JITPLL

PLL jitter (

Δf

CPU/fCPU)1

(6)

IDD(PLL)

PLL current

consumption

TA=25° C

600(3)

μA

If the RC oscillator clock is selected, to improve clock stability and frequency accuracy, it is recommended to place a decoupling capacitor,

typically 100nF, between the VDD and VSS pins as close as possible to the ST7 device.

See Section 9.2: Internal RC oscillator adjustment on page 32

Data based on characterization results, not tested in production

After the LOCKED bit is set ACCPLL is max. 10% until tSTAB has elapsed. See Figure 11 on page 34.

Averaged over a 4ms period. After the LOCKED bit is set, a period of tSTAB is required to reach ACCPLL accuracy.

Guaranteed by design.

ST7DALIF2 Datasheet(PDF) 132 Page - STMicroelectronics

ST7DALIF2 Datasheet(HTML) 132 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL