ADATE302-02BBCZ datasheet(18/59 Pages) AD

18 / 59 page

ADATE302-02

Rev. A | Page 17 of 58

DUTGND INPUT

Table 9.

Parameter

Min

Typ

Max

Unit

Test

Level

Conditions/Comments

Input Voltage Range, Referenced to GND

−0.1

+0.1

Input Bias Current

100

μA

Tested at −100 mV and +100 mV

SERIAL PERIPHERAL INTERFACE

Table 10.

Parameter

Min

Typ

Max

Unit

Test

Level

Conditions/Comments

Serial Input Logic High

1.8

VCC

Serial Input Logic Low

0.7

Input Bias Current

−10

+10

μA

Tested at 0.0 V and 3.3 V

SCLK Clock Rate

MHz

SCLK Pulse Width

SCLK Crosstalk on DUTx Pin

PE disabled, PMU FV enabled and forcing 0 V

Serial Output Logic High

VCC − 0.4

VCC

Sourcing 2 mA

Serial Output Logic Low

0.8

Sinking 2 mA

Update Time

μs

Maximum delay time required for the part to enter

a stable state after a serial bus command is loaded

HVOUT DRIVER

Table 11.

Parameter

Min

Typ

Max

Unit

Test

Level

Conditions/Comments

VHH BUFFER

VHH = (VT + 1 V) × 2 + DUTGND

Voltage Range

5.9

VPLUS − 3.25

VPLUS = 16.75 V nominal; in this condition,

VHVOUT maximum = 13.5 V

Output High

13.5

VHH mode enabled, RCVx pins active, VHH level = full

scale, sourcing 15 mA

Output Low

5.9

VHH mode enabled, RCVx pins active, VHH level = zero

scale, sinking 15 mA

Accuracy Uncalibrated

−500

±100

+500

VHH mode enabled, RCVx pins active, VHVOUT error

measured at calibration points of 7 V and 12 V

Offset Tempco

mV/°C

Measured at calibration points

Resolution

1.21

1.5

VHH mode enabled, RCVx pins active, after two-point

gain/offset calibration; range/number of DAC bits as

measured at calibration points of 7 V and 12 V

INL

−30

±15

+30

VHH mode enabled, RCVx pins active, after two-point gain/

offset calibration; measured over VHH range of 5.9 V to 13.5 V

DUTGND Voltage Accuracy

±1

Over ±0.1 V range; measured at end points of VHH

functional range

Output Resistance

VHH mode enabled, RCVx pins active, source: VHH = 10.0 V,

IHVOUT = 0 mA and 15 mA; sink: VHH = 6.5 V, IHVOUT = 0 mA

and −15 mA; ΔV/ΔI

DC Output Current Limit Source

100

VHH mode enabled, RCVx pins active, VHH = 10.0 V, short

HVOUT pin to 5.9 V, measure current

DC Output Current Limit Sink

−100

−60

VHH mode enabled, RCVx pins active, VHH = 6.5 V, short

HVOUT pin to 14.1 V, measure current

Rise Time (From VL or VH to

VHH)

175

VHH mode enabled, toggle RCVx pins, VHH = 13.5 V, VL =

VH = 3.0 V; 20% to 80%, for DATAx high and DATAx low

ADATE302-02BBCZ Datasheet(PDF) 18 Page - Analog Devices

ADATE302-02BBCZ Datasheet(HTML) 18 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59

Datasheet Download

Link URL