Electronic Components Datasheet Search
  English  ▼

X  

BDP1A Datasheet(PDF) 3 Page - Agere Systems

Part # BDP1A
Description  QUAD DIFFERENTIAL DRIVERS
PDF  16 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AGERE [Agere Systems]
Direct Link  
Logo AGERE - Agere Systems

BDP1A Datasheet(HTML) 3 Page - Agere Systems

  BDP1A Datasheet HTML 1Page - Agere Systems BDP1A Datasheet HTML 2Page - Agere Systems BDP1A Datasheet HTML 3Page - Agere Systems BDP1A Datasheet HTML 4Page - Agere Systems BDP1A Datasheet HTML 5Page - Agere Systems BDP1A Datasheet HTML 6Page - Agere Systems BDP1A Datasheet HTML 7Page - Agere Systems BDP1A Datasheet HTML 8Page - Agere Systems BDP1A Datasheet HTML 9Page - Agere Systems Next Button
Zoom Inzoom in Zoom Outzoom out
 3 / 16 page
background image
Agere Systems Inc.
3
Data Sheet
January 1999
BDG1A, BDP1A, BDGLA, BPNGA, BPNPA, and BPPGA
Quad Differential Drivers
Electrical Characteristics
For electrical characteristics over the entire temperature range, see Figures 7 through 9.
Table 2. Power Supply Current Characteristics
TA = –40 °C to +125 °C, VCC = 5 V
± 0.5 V.
* Measured with no load (BPPGA has no load on drivers C and D).
† The additional power dissipation is the result of integrating the termination resistors into the device. ICC is measured with a 100
Ω resistor
across the driver outputs (BPPGA has terminating resistors on drivers A and B).
Third State
These drivers produce pseudo-ECL levels, and the third-state mode is different than the conventional TTL devices.
When a driver is placed in the third state, the bases of the output transistors are pulled low, bringing the outputs
below the active-low levels. This voltage is typically 2 V for most drivers. In the bidirectional bus application, the
driver of one device, which is in its third state, may be back driven by another driver on the bus whose voltage in
the low state is lower than the third-stated device. This could come about due to differences in the drivers’ indepen-
dent power supplies. In this case, the device in the third state will control the line, thus clamping the line and reduc-
ing the signal swing. If the difference voltage between the independent power supplies and the drivers is small,
then this consideration can be ignored. In the typical case, the difference voltage can be as much as 1 V without
significantly affecting the amplitude of the driving signal.
Parameter
Symbol
Min
Typ
Max
Unit
Power Supply Current (VCC = 5.5 V):
All Outputs Disabled:
BDG1A*, BPNGA*
ICC
45
65
mA
BDP1A†, BPNPA†
ICC
120
160
mA
BDGLA*
ICC
35
55
mA
BPPGA*†
ICC
85
115
mA
All Outputs Enabled:
BDG1A*, BPNGA*
ICC
25
40
mA
BDP1A†, BPNPA†
ICC
150
200
mA
BDGLA*
ICC
14
20
mA
BPPGA*†
ICC
90
115
mA



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com