Electronic Components Datasheet Search
  English  ▼

X  

LTM4609 Datasheet(PDF) 11 Page - Linear Technology

Part # LTM4609
Description  40A 關Module Regulator with Overvoltage/ Overtemperature Protection
PDF  38 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  LINER [Linear Technology]
Direct Link  http://www.linear.com
Logo LINER - Linear Technology

LTM4609 Datasheet(HTML) 11 Page - Linear Technology

Back Button LTM4609 Datasheet HTML 7Page - Linear Technology LTM4609 Datasheet HTML 8Page - Linear Technology LTM4609 Datasheet HTML 9Page - Linear Technology LTM4609 Datasheet HTML 10Page - Linear Technology LTM4609 Datasheet HTML 11Page - Linear Technology LTM4609 Datasheet HTML 12Page - Linear Technology LTM4609 Datasheet HTML 13Page - Linear Technology LTM4609 Datasheet HTML 14Page - Linear Technology LTM4609 Datasheet HTML 15Page - Linear Technology Next Button
Zoom Inzoom in Zoom Outzoom out
 11 / 38 page
background image
LTM4636-1
11
46361fa
For more information www.linear.com/LTM4636-1
DECOUPLING REQUIREMENTS
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
CIN
External Input Capacitor Requirement
(VIN = 4.70V to 16V, VOUT = 1.5V)
IOUT = 40A, 6 × 22µF Ceramic X7R Capacitors
(See Table 4)
100
µF
COUT
External Output Capacitor Requirement
(VIN = 4.70V to 16V, VOUT = 1.5V)
IOUT = 40A (See Table 4)
1000
µF
TA = 25°C. Use Figure 1 configuration.
Power Module Description
The LTM4636-1 is a high efficiency regulator that can
provide a 40A output with few external input and output
capacitors.Thismoduleprovidespreciselyregulatedoutput
voltagesprogrammableviaexternalresistorsfrom0.6VDC
to 3.3V DC over a 4.70V to 15V input range. The Typical
ApplicationschematicwithprotectionisshowninFigure20.
The LTM4636-1 has an integrated constant-frequency
current mode regulator, power MOSFETs, 0.18µH induc-
tor, protection circuitry, 5V regulator and other supporting
discrete components. The switching frequency range is
from250kHzto770kHz,andthetypicaloperatingfrequency
is 400kHz. For switching noise-sensitive applications, it
can be externally synchronized from 250kHz to 800kHz,
subject to minimum on-time limitations and limiting the
inductor ripple current to less than 40% of maximum
output current.
A single resistor is used to program the frequency. See
the Applications Information section.
With current mode control and internal feedback loop
compensation, the LTM4636-1 module has sufficient sta-
bility margins and good transient performance with a wide
range of output capacitors, even with all ceramic output
capacitors. An option has been provided for external loop
compensation. LTpowerCAD™ can be used to optimize
the external compensation option. See the Applications
Information section.
Current mode control provides cycle-by-cycle fast current
limit in an overcurrent condition. An internal overvoltage
monitor feedback pin referred will attempt to protect the
output voltage in the event of an overvoltage >10%. The
top MOSFET is turned off and the bottom MOSFET is
turned on until the output is cleared.
OPERATION
Pulling the RUNC pin below 1.1V forces the regulator con-
trollerintoashutdownstate.TheTRACK/SSpinisusedfor
programmingtheoutputvoltagerampandvoltagetracking
during start-up. See the Applications Information section.
Optional internal overvoltage protection and overtem-
perature functions can be used to protect from power
MOSFET failures, input and output overvoltage and over-
temperature conditions. These two features can be used
to trip off and retry an input circuit breaker in the event
of either/or both an overvoltage and overtemperature
fault. The OVP_TRIP, OVER_TEMP, TMON, OVP_SET,
CROWBARandOTP_SETpinsareallusedtosupportthese
two features. These features can be implemented along
with an input circuit breaker to protect expensive systems
boards, processors and FPGA devices from damage. See
the Applications Information section.
The LTM4636-1 is internally compensated to be stable
over all operating conditions. Table 5 provides a guideline
for input and output capacitances for several operating
conditions. LTpowerCAD is available for transient and
stability analysis. This tool can be used to optimize the
regulators loop response.
Aremotesenseamplifierisprovidedforaccuratelysensing
output voltages at the load point.
Multiphase operation can be easily employed with the
internal clock source or a synchronization clock applied
to the MODE/PLLIN input using an external clock source,
and connecting the CLKOUT pins. See the Applications
Information section. Review Figure 4.
High efficiency at light loads can be accomplished with
selectable Burst Mode operation using the MODE_PLLIN
pin. These light load features will accommodate battery
operation. Efficiency graphs are provided for light load op-
erationintheTypicalPerformanceCharacteristicssection.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com