Electronic Components Datasheet Search
  English  ▼

X  

LTM4615 Datasheet(PDF) 11 Page - Linear Technology

Part # LTM4615
Description  Low VIN 20A DC/DC 關Module Step-Down Regulator
PDF  32 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  LINER [Linear Technology]
Direct Link  http://www.linear.com
Logo LINER - Linear Technology

LTM4615 Datasheet(HTML) 11 Page - Linear Technology

Back Button LTM4615 Datasheet HTML 7Page - Linear Technology LTM4615 Datasheet HTML 8Page - Linear Technology LTM4615 Datasheet HTML 9Page - Linear Technology LTM4615 Datasheet HTML 10Page - Linear Technology LTM4615 Datasheet HTML 11Page - Linear Technology LTM4615 Datasheet HTML 12Page - Linear Technology LTM4615 Datasheet HTML 13Page - Linear Technology LTM4615 Datasheet HTML 14Page - Linear Technology LTM4615 Datasheet HTML 15Page - Linear Technology Next Button
Zoom Inzoom in Zoom Outzoom out
 11 / 32 page
background image
LTM4639
11
4639f
For more information www.linear.com/LTM4639
APPLICATIONS INFORMATION
The typical LTM4639 application circuit is shown in Fig-
ure 22. External component selection is primarily
determined by the maximum load current and output
voltage. Refer to Table 5 for specific external capacitor
requirements for particular applications.
VIN to VOUT Step-Down Ratios
There are restrictions in the VIN to VOUT step-down ratio
that can be achieved for a given input voltage. The duty
cycle is 94% typical at 500kHz operation. The VIN to VOUT
minimumdropoutisafunctionofloadcurrentandoperation
at very low input voltage and high duty cycle applications.
At very low duty cycles the minimum 100ns on-time must
be maintained. See the Frequency Adjustment section and
temperature derating curves.
Output Voltage Programming
The PWM controller has an internal 0.6V ±1% reference
voltage. As shown in the Block Diagram, a 60.4k internal
feedback resistor connects the VOUT_LCL and VFB pins
together. When the remote sense amplifier is used, then
DIFF_OUT is connected to the VOUT_LCL pin. If the remote
sense amplifier is not used, then VOUT_LCL connects to
VOUT. The output voltage will default to 0.6V with no
feedbackresistor.AddingaresistorRFBfromVFBtoground
programs the output voltage:
VOUT= 0.6V •
60.4k+RFB
RFB
Table 1. VFB Resistor Table vs Various Output Voltages
VOUT (V) 0.6
1.0
1.2
1.5
1.8
2.5
3.3
5.0
RFB (k)
Open 90.9
60.4
40.2
30.1
19.1
13.3
8.25
For parallel operation of N LTM4639s, the following
equation can be used to solve for RFB:
RFB=
60.4k /N
VOUT
0.6V
–1
Tie the VFB pins together for each parallel output. The
COMP pins must be tied together also.
Input Capacitors
The LTM4639 module should be connected to a low AC-
impedance DC source. Additional input capacitors are
neededfortheRMSinputripplecurrentrating.TheICIN(RMS)
equation which follows can be used to calculate the input
capacitor requirement. Typically 22µF X7R ceramics are a
good choice with RMS ripple current ratings of ~ 2A each.
A47µFto100µFsurfacemountaluminumelectrolyticbulk
capacitor can be used for more input bulk capacitance.
This bulk input capacitor is only needed if the input source
impedanceiscompromisedbylonginductiveleads,traces
ornotenoughsourcecapacitance.Iflowimpedancepower
planes are used, then this bulk capacitor is not needed.
For a buck converter, the switching duty cycle can be
estimated as:
D=
VOUT
VIN
Without considering the inductor ripple current, for each
output the RMS current of the input capacitor can be
estimated as:
ICIN(RMS)=
IOUT(MAX)
η%
• D•(1–D)
where η% is the estimated efficiency of the power module.
The bulk capacitor can be a switcher-rated aluminum
electrolytic capacitor or a Polymer capacitor.
Output Capacitors
The LTM4639 is designed for low output voltage ripple
noise. The bulk output capacitors defined as COUT are
chosen with low enough effective series resistance
(ESR) to meet the output voltage ripple and transient
requirements. COUT can be a low ESR tantalum capacitor,
low ESR Polymer capacitor or ceramic capacitors. The
typical output capacitance range is from 200µF to 800µF.
Additional output filtering may be required by the system
designer if further reduction of output ripple or dynamic
transient spikes is required. Table 5 shows a matrix
of different output voltages and output capacitors to
minimizethevoltagedroopandovershootduringa10A/µs
transient.ThetableoptimizestotalequivalentESRandtotal
bulk capacitance to optimize the transient performance.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com