Electronic Components Datasheet Search
  English  ▼

X  

LTM4615 Datasheet(PDF) 17 Page - Linear Technology

Part # LTM4615
Description  Low VIN 20A DC/DC 關Module Step-Down Regulator
PDF  32 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  LINER [Linear Technology]
Direct Link  http://www.linear.com
Logo LINER - Linear Technology

LTM4615 Datasheet(HTML) 17 Page - Linear Technology

Back Button LTM4615 Datasheet HTML 13Page - Linear Technology LTM4615 Datasheet HTML 14Page - Linear Technology LTM4615 Datasheet HTML 15Page - Linear Technology LTM4615 Datasheet HTML 16Page - Linear Technology LTM4615 Datasheet HTML 17Page - Linear Technology LTM4615 Datasheet HTML 18Page - Linear Technology LTM4615 Datasheet HTML 19Page - Linear Technology LTM4615 Datasheet HTML 20Page - Linear Technology LTM4615 Datasheet HTML 21Page - Linear Technology Next Button
Zoom Inzoom in Zoom Outzoom out
 17 / 32 page
background image
LTM4639
17
4639f
For more information www.linear.com/LTM4639
To obtain a linear voltage proportional to temperature,
we cancel the IS variable in the natural logarithm term to
remove the IS dependency from the following equation.
This is accomplished by measuring the diode voltage at
two currents I1, and I2, where I1 = 10 • I2
Subtracting we get:
∆VD = T(KELVIN)•KD •In
I1
IS
− T(KELVIN) •KD •In
I2
IS
Combining like terms, then simplifying the natural log
terms yields:
∆VD = T(KELVIN) • KD • In(10)
and redefining constant
K’D = KD • In(10) = 198µV/k
yields
∆VD = K’D • T(KELVIN)
Solving for temperature:
T(KELVIN) = ∆VD
K'D
,
T(KELVIN) =[°C]+ 273.15,
[°C]= T(KELVIN)− 273.15
means that is we take the difference in voltage across the
diode measured at two currents with a ratio of 10, the
resulting voltage is 198µV per Kelvin of the junction with
a zero intercept at 0 Kelvin.
The diode connected PNP transistor at the TEMP+, TEMP–
pins can be used to monitor the internal temperature of
the LTM4639. A general temperature monitor can be
implemented by connecting a resistor between TEMP+
and VIN to set the current to 100µA, grounding the TEMP–
pin, and then monitoring the diode voltage drop with
temperature. A more accurate temperature monitor can
be achieved with a circuit injecting two currents that are
at a 10:1 ratio. See Figure 22 for an example.
Overtemperature Protection
The internal overtemperature protection monitors the
internal temperature of the module and shuts off the
regulator at ~130°C to 137°C. Once the regulator cools
down the regulator will restart.
Run Enable
The RUN pin is used to enable the power module or
sequence the power module. The threshold is 1.25V, and
the pin has an internal 5.1V Zener to protect the pin. The
RUN pin can be used as an undervoltage lockout (UVLO)
function by connecting a resistor divider from the input
supply to the RUN pin:
VUVLO = ((R1+R2)/R2) • 1.25V
See Figure 1, Simplified Block Diagram.
INTVCC Regulator
The LTM4639 has an internal low dropout regulator from
VIN called INTVCC. This regulator output has a 2.2µF
ceramic capacitor internal. An additional 2.2µF ceramic
capacitor is needed on this pin to ground. This regulator
powers the internal controller and MOSFET drivers. The
gate driver current is ~20mA for 750kHz operation. The
regulator loss can be calculated as:
(VIN – 5V) • 20mA = PLOSS
EXTVCC external voltage source ≥ 4.7V can be applied to
thispintoeliminatetheinternalINTVCCLDOpowerlossand
increase regulator efficiency. A 5V supply can be applied
to run the internal circuitry and power MOSFET driver. If
unused, leave pin floating. EXTVCC must be less than VIN
at all times during power-on and power-off sequences.
Stability Compensation
TheLTM4639hasalreadybeeninternallycompensatedfor
alloutputvoltages.Table5isprovidedformostapplication
requirements. LTpowerCAD is available for other control
loop optimization.
Thermal Considerations and Output Current Derating
The thermal resistances reported in the Pin Configuration
section of the data sheet are consistent with those
parametersdefinedbyJESD51-12andareintendedforuse
withfiniteelementanalysis(FEA)softwaremodelingtools
thatleveragetheoutcomeofthermalmodeling,simulation,
and correlation to hardware evaluation performed on a
µModule package mounted to a hardware test board.
The motivation for providing these thermal coefficients
in found in JESD51-12 (“Guidelines for Reporting and
Using Electronic Package Thermal Information”).
APPLICATIONS INFORMATION



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com