| Electronic Components Datasheet Search |
|
LTM4615 Datasheet(PDF) 12 Page - Linear Technology |
|
|
|||||||||||||||||||||||||||||
LTM4615 Datasheet(HTML) 12 Page - Linear Technology |
|
12 / 32 page ![]() LTM4639 12 4639f For more information www.linear.com/LTM4639 Stability criteria are considered in the Table 5 matrix, and LTpowerCAD is available for stability analysis and custom compensation for loop optimization using the COMPA pin. Multiphase operation will reduce effective output ripple as a function of the number of phases. Application Note 77 discusses this noise reduction versus output ripple current cancellation, but the output capacitance should be considered carefully as a function of stability and transient response.LTpowerCADcanbeusedtocalculatetheoutput ripple reduction as the number of implemented phases increase by N times. Burst Mode Operation The LTM4639 is capable of Burst Mode operation in which the power MOSFETs operate intermittently based on load demand, thus saving quiescent current. For applications where maximizing the efficiency at very light loads is a high priority, Burst Mode operation should be applied. To enableBurstModeoperation,simplyfloattheMODE_PLLIN pin. During Burst Mode operation, the peak current of the inductorissettoapproximately30%ofthemaximumpeak current value in normal operation even though the voltage at the COMPA pin indicates a lower value. The voltage at the COMPA pin drops when the inductor’s average current isgreaterthantheloadrequirement.AstheCOMPAvoltage drops below 0.5V, the burst comparator trips, causing the internal sleep line to go high and turn off both power MOSFETs. In sleep mode, the internal circuitry is partially turned off, reducing the quiescent current. The load current is now being supplied from the output capacitors. When the output voltage drops, causing COMPA to rise, the internal sleep line goes low, and the LTM4639 resumes normal operation. The next oscillator cycle will turn on the top power MOSFET and the switching cycle repeats. Pulse-Skipping Mode Operation In applications where low output ripple and high effi- ciency at intermediate currents are desired, pulse- skipping mode should be used. Pulse-skipping operation allows the LTM4639 to skip cycles at low output loads, thusincreasingefficiencybyreducingswitchingloss.Tying the MODE_PLLIN pin to INTVCC enables pulse-skipping operation. With pulse-skipping mode at light load, the internalcurrentcomparatormayremaintrippedforseveral cycles, thus skipping operation cycles. This mode has lower ripple than Burst Mode operation and maintains a higher frequency operation than Burst Mode operation. Forced Continuous Operation In applications where fixed frequency operation is more critical than low current efficiency, and where the lowest output ripple is desired, forced continuous operation should be used. Forced continuous operation can be enabled by tying the MODE_PLLIN pin to ground. In this mode, inductor current is allowed to reverse during low outputloads,theCOMPAvoltageisincontrolofthecurrent comparator threshold throughout, and the top MOSFET alwaysturnsonwitheachoscillatorpulse.Duringstart-up, forced continuous mode is disabled and inductor current is prevented from reversing until the LTM4639’s output voltage is in regulation. Multiphase Operation For outputs that demand more than 20A of load current, multiple LTM4639 devices can be paralleled to provide more output current without increasing input and output ripple voltage. The MODE_PLLIN pin allows the LTM4639 to be synchronized to an external clock and the internal phase-locked loop allows the LTM4639 to lock onto input clockphaseaswell.ThefSETresistorisselectedfornormal frequency, then the incoming clock can synchronize the device over the specified range. See Figure 24 for a synchronizing example circuit. A multiphase power supply significantly reduces the amount of ripple current in both the input and output capacitors.TheRMSinputripplecurrentisreducedby,and the effective ripple frequency is multiplied by, the number of phases used (assuming that the input voltage is greater than the number of phases used times the output voltage). The output ripple amplitude is also reduced by the number of phases used. See Application Note 77. The LTM4639 device is an inherently current mode controlled device, so parallel modules will have good current sharing. This will balance the thermals in the design. Tie the COMPA and VFB pins of each LTM4639 APPLICATIONS INFORMATION |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |