Electronic Components Datasheet Search
  English  ▼

X  

LT6237 Datasheet(PDF) 28 Page - Linear Technology

Part # LT6237
Description  16-Bit, 1Msps, 8-Channel SAR ADC with 96dB SNR
PDF  52 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  LINER [Linear Technology]
Direct Link  http://www.linear.com
Logo LINER - Linear Technology

LT6237 Datasheet(HTML) 28 Page - Linear Technology

Back Button LT6237 Datasheet HTML 24Page - Linear Technology LT6237 Datasheet HTML 25Page - Linear Technology LT6237 Datasheet HTML 26Page - Linear Technology LT6237 Datasheet HTML 27Page - Linear Technology LT6237 Datasheet HTML 28Page - Linear Technology LT6237 Datasheet HTML 29Page - Linear Technology LT6237 Datasheet HTML 30Page - Linear Technology LT6237 Datasheet HTML 31Page - Linear Technology LT6237 Datasheet HTML 32Page - Linear Technology Next Button
Zoom Inzoom in Zoom Outzoom out
 28 / 52 page
background image
LTC2373-16
28
237316fa
For more information www.linear.com/LTC2373-16
237316 F12c
47µF
6.5k
15k
LTC2373-16
REFERENCE
BUFFER
REFBUF
REFIN
GND
BANDGAP
REFERENCE
6.5k
LTC6655-5
Figure 12c. Overdriving REFBUF Using the LTC6655-5
manyapplications.Withitssmallsize,lowpower,andhigh
accuracy, the LTC6655-2.048 is well suited for use with
the LTC2373-16 when overdriving the internal reference.
The LTC6655-2.048 offers 0.025% (max) initial accuracy
and 2ppm/°C (max) temperature coefficient for high pre-
cision applications. The LTC6655-2.048 is fully specified
over the H-grade temperature range and complements
the extended temperature range of the LTC2373-16 up to
125°C.BypassingtheLTC6655-2.048witha2.7μFto100μF
ceramic capacitor close to the REFIN pin is recommended.
External Reference Unbuffered
The internal reference buffer can also be overdriven from
2.5V to 5V with an external reference at REFBUF as shown
inFigure12c.Todoso,REFINmustbegroundedtodisable
the reference buffer. A 13k resistor loads the REFBUF pin
whenthereferencebufferisdisabled.Tomaximizetheinput
signal swing and corresponding SNR, the LTC6655-5 is
recommendedwhenoverdrivingREFBUF.TheLTC6655-5
offers the same small size, accuracy, drift and extended
temperature range as the LTC6655-2.048. By using a 5V
reference, an SNR of 97dB can be achieved. Bypassing
the LTC6655-5 with a 47μF ceramic capacitor (X5R, 0805
size) close to the REFBUF pin is recommended.
applicaTions inForMaTion
Figure 13. CNV Waveform Showing Burst Sampling
external reference must provide all of this charge with a
DC current equivalent to IREFBUF = QCONV/tCYC. Thus, the
DC current draw of REFBUF depends on the sampling rate
and output code. In applications where a burst of samples
is taken after idling for long periods, as shown in Figure 13,
IREFBUF quickly goes from approximately 380µA to a maxi-
mum of 1.2mA for REFBUF = 5V at 1Msps. This step in DC
current draw triggers a transient response in the external
reference that must be considered since any deviation in
the voltage at REFBUF will affect the accuracy of the output
code. If an external reference is used to overdrive REFBUF,
the fast settling LTC6655-5 reference is recommended.
Internal Reference Buffer Transient Response
Foroptimumtransientperformance,theinternalreference
buffer should be used. The internal reference buffer uses a
proprietary design that results in an output voltage change
at REFBUF of less than 1LSB when responding to a sudden
burst of conversions. This makes the internal reference
buffer of the LTC2373-16 truly single-shot capable since
the first sample taken after idling will yield the same re-
sult as a sample taken after the transient response of the
internal reference buffer has settled. Figures 14a, 14b,
and 14c show the transient responses of the LTC2373-
16 with the internal reference buffer and with the internal
reference buffer overdriven by the LTC6655-5, both with
a bypass capacitance of 47μF in fully differential, pseudo-
differential unipolar, and pseudo-differential bipolar input
ranges, respectively.
DYNAMIC PERFORMANCE
Fast fourier transform (FFT) techniques are used to test the
ADC’s frequency response, distortion and noise at the rated
throughput. By applying a low distortion sine wave and ana-
lyzing the digital output using an FFT algorithm, the ADC’s
spectralcontentcanbeexaminedforfrequenciesoutsidethe
fundamental. The LTC2373-16 provides guaranteed tested
limits for both AC distortion and noise measurements.
CNV
IDLE
PERIOD
IDLE
PERIOD
237316 F13
TheREFBUFpinoftheLTC2373-16drawsacharge(QCONV)
fromtheexternalbypasscapacitorduringeachconversion
cycle. If the internal reference buffer is overdriven, the



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com