Electronic Components Datasheet Search
  English  ▼

X  

NM95HS02EN Datasheet(PDF) 17 Page - National Semiconductor (TI)

[Old version datasheet] Texas Instruments acquired National semiconductor.
Part # NM95HS02EN
Description  HiSeC-TM High Security Rolling Code Generator
PDF  20 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  NSC [National Semiconductor (TI)]
Direct Link  http://www.national.com
Logo NSC - National Semiconductor (TI)

NM95HS02EN Datasheet(HTML) 17 Page - National Semiconductor (TI)

Back Button NM95HS02EN Datasheet HTML 12Page - National Semiconductor (TI) NM95HS02EN Datasheet HTML 13Page - National Semiconductor (TI) NM95HS02EN Datasheet HTML 14Page - National Semiconductor (TI) NM95HS02EN Datasheet HTML 15Page - National Semiconductor (TI) NM95HS02EN Datasheet HTML 16Page - National Semiconductor (TI) NM95HS02EN Datasheet HTML 17Page - National Semiconductor (TI) NM95HS02EN Datasheet HTML 18Page - National Semiconductor (TI) NM95HS02EN Datasheet HTML 19Page - National Semiconductor (TI) NM95HS02EN Datasheet HTML 20Page - National Semiconductor (TI)  
Zoom Inzoom in Zoom Outzoom out
 17 / 20 page
background image
Programming the NM95HS0102
The NM95HS0102 HiSeC Generator uses four pins to read
and write the 13 bytes of on-chip EEPROM These are the
Key1 (K1) Key2 (K2) TX and CKI pins K1 functions as the
chip select line K2 functions as the data strobe CKI serves
as the serial clock and TX acts as the data out pin
Three voltage levels are required to program the device
Supervoltage (VSV) ReadWrite voltage (VRW) and Ground
(0V) Supervoltage is used to select Read and Write modes
in the device These modes can only be entered by applying
supervoltage to K1 and K2 This alleviates the risk of the
device entering these modes during normal operation
The programming protocol for the NM95HS0102 on-chip
EEPROM array was designed to match National Semicon-
ductor’s MICROWIRE format closely However there are
several differences One is the need to use a supervoltage
to select modes Another concerns the CKI clock input
Upon power-up the NM95HS0102 CKI input must be
clocked a minimum of 1500 times to ensure the part is ready
for programming This allows the internal state machines
and registers to perform their necessary power-on se-
quences (See Table VII)
Write Mode
The NM95HS0102 HiSeC Generator can be placed in
Write mode when supervoltage is applied to both K1 and K2
in a specific sequence Upon power-up both K1 and K2
must be set to VRW and a minimum of 1500 clock
pulses applied to CKI to initialize the part (See Timing Dia-
gram on pg 16) After this initialization K2 is brought to
supervoltage K1 is then brought to supervoltage Now K2 is
brought back to VRW then K1 is brought back to VRW The
NM95HS0102 is now in Write mode
To program the first byte set K1 back to supervoltage and
place the first byte of data (VIH and VIL pulses) onto K2
(starting with the Least Significant Bit) As each bit is placed
on K2 clock the CKI pin to latch the bit When all bits of the
first byte have been latched in set K1 to VRW and poll the
TX output pin for a logic low
This confirms the
NM95HS0102 has written the byte to memory Repeat this
sequence to program the remainder of the bytes When all
13 bytes have been programmed set K1 and K2 to 0V to
end Write mode
Read Mode
The NM95HS0102 HiSeC Generator can be placed in
Read mode by applying supervoltage to K1 Upon power-
up both K1 and K2 must be set to VRW and a minimum of
1500 clock pulses applied to CKI to initialize the part (See
Timing Diagram on pg 16) After this initialization K1 is
brought to supervoltage Then K1 is brought back to VRW
The NM95HS0102 is now in Read mode
To read the first byte set K1 back to supervoltage and
clock the CKI pin 8 times while polling TX EEPROM data is
sent Most Significant Bit first Continue clocking CKI to read
the remainder of the bytes When all 13 bytes have been
read set K1 back to VRW Set K1 and K2 to 0V to end Read
mode
Programmer Support for NM95HS0102
Worldwide third party support is provided by
Vendor
Contact Number
Xeltek
Europe 49-5722-203-125 (Germany)
SuperPro-EM
America 408-524-1929
Universal
Asia 65-296-6433 (Singapore)
Programmer
BBS 408-245-7082
National Semiconductor
Americas 800-272-9959
NM95HS-PRO-X
System General
Switzerland 31-921-7844
Turpro-1 Univeral
America 408-263-6667800-967-4776
Device Programmer
Taiwan 886-2-917-3015
BBS 408-262-6438
Hi-Lo ALL-07
Asia 886-2764-0215
America 510-623-3850
Evalutation kit support for NM95HS0102 A demonstration kit for the
HiSeC High Security Rolling Code Generator is available
National Semiconductor
NM95HSEV
HiSeC Evaluation Board
NM95HSPRO
HiSeC Single Site Programmer
http
www nationalcom
17



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com