Electronic Components Datasheet Search
  English  ▼

X  

NM95HS02EN Datasheet(PDF) 12 Page - National Semiconductor (TI)

[Old version datasheet] Texas Instruments acquired National semiconductor.
Part # NM95HS02EN
Description  HiSeC-TM High Security Rolling Code Generator
PDF  20 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  NSC [National Semiconductor (TI)]
Direct Link  http://www.national.com
Logo NSC - National Semiconductor (TI)

NM95HS02EN Datasheet(HTML) 12 Page - National Semiconductor (TI)

Back Button NM95HS02EN Datasheet HTML 8Page - National Semiconductor (TI) NM95HS02EN Datasheet HTML 9Page - National Semiconductor (TI) NM95HS02EN Datasheet HTML 10Page - National Semiconductor (TI) NM95HS02EN Datasheet HTML 11Page - National Semiconductor (TI) NM95HS02EN Datasheet HTML 12Page - National Semiconductor (TI) NM95HS02EN Datasheet HTML 13Page - National Semiconductor (TI) NM95HS02EN Datasheet HTML 14Page - National Semiconductor (TI) NM95HS02EN Datasheet HTML 15Page - National Semiconductor (TI) NM95HS02EN Datasheet HTML 16Page - National Semiconductor (TI) Next Button
Zoom Inzoom in Zoom Outzoom out
 12 / 20 page
background image
Security Aspects
NORMAL OPERATION
Once the NM95HS0102 has been initialized the device will
generate and transmit a new code each time a key is
pressed If a key is held down the same frame (plus any
pauses between frames) is transmitted repeatedly If the
key is held down for longer than 80 seconds the generator
will go into halt mode to conserve battery power and will
stop transmitting data frames (if the TIMEOUTEN option is
enabled)
Another option available during normal generator operation
is the ability to generate a resync after a key has been
pressed for more than 10 seconds (if the AutoResync op-
tion is enabled) This option allows the end user to resyn-
chronize the generator if necessary without having to re-
move and replace the battery
FORWARD CALCULATION AND CODE WINDOWS
Aside from using a sync frame there is another way to en-
sure the NM95HS0102 remains in sync with its decoder
during normal operation The decoder can perform a for-
ward calculation to predict what the next generator codes
will be This is an important point and should be considered
carefully in designing the decoding system
In a well-designed system the decoder should be able to
calculate forward for some reasonable number of codes
and store the results for future reference This allows the
decoder to remain in sync even if it misses one or more
codes from the generator This could occur if the receiver
did not receive a transmission clearly or if someone activat-
ed the keys outside the range of the receiver
Increasing the depth of this code window would allow the
decoder to miss a greater number of codes from the gener-
ator and still remain in sync One method for implementing
a code window is to include a MICROWIRETM EEPROM
(such as the NM93Cx6) in the decoder design and store the
codes in memory This becomes even more important if the
decoder is designed to accomodate several HiSeC genera-
tor devices In this case the decoder should have a code
window available for each device
Generator Clock Design
Parameters
Tables IV V and VI provide a basis for selecting component
values for both the RC clocked generator (NM95HS01) and
the
crystal
(XTAL)
oscillator
clocked
generator
(NM95HS02)
The component values shown in the tables have been cho-
sen for low cost general availability and reliable operation
Components are referenced to the circuit schematics
shown in
Figure 3 Though there is some flexibility in select-
ing alternate values there are constraints on permissible
component values
All resistors and capacitors should be kept within the follow-
ing ranges 3 kX s Rx s 200 kX and 50 pF s Cx s 200 pF
TABLE IV RC Clock Components
TA e 25 C VCC e 5V–65V
R(kX)
C (pF)
CKI (MHz)
CKI (ns)
33
82
212 – 232
470 – 430
56
100
11 – 117
870 – 850
68
100
09 – 095
1100 – 1050
TABLE V RC Clock Components
TA e 25 C VCC e 25V
R(kX)
C (pF)
CKI (MHz)
CKI (ns)
33
82
153 – 16
650 – 600
56
100
09 – 1
1100 – 1000
68
100
08 – 083
1250 – 1200
TABLE VI XTAL Clock Components
TA e 25 C VCC e 25V–65V
R1 (MX)
C1 (pF)
C2 (pF)
CKI (MHz)
CKI (ns)
1
30
30–36
4
250
http
www nationalcom
12



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com