738A INSTALLATION GUIDE

|

DIGITAL MONITORING PRODUCTS

3

ZONE NO:

ZONE NUMBER

After selecting

ADD, enter a wireless transmitter zone number to be programmed into the

module at the Zone Number option. Press

CMD to accept the zone number.

This zone number must correspond to a zone number programmed into the panel.

When the module is connected to the Keypad Bus and any wireless input zones for a

particular address are programmed (Ex: 11‑14 = Addr 1), the module responds to polls for this

address. Other devices, such as keypads, cannot use this address. For more information about

addressing the module, refer to Table 1 and Table 2.

*UN

RF

UR BR

TRANSMITTER TYPE

Enter a transmitter type by pressing the select key that corresponds to the type of transmitter

used. An asterisk appears to the left of the transmitter type chosen. Default is

UN. Press

the

CMD key to accept the selection. Refer to the installation instructions provided with the

Ademco transmitter for additional information.

UN = Unused Zone

UR = Unsupervised Transmitter

RF = Supervised Transmitter

BR = Button Transmitter

When a transmitter reed switch, contact, or button is in a faulted condition, the corresponding

panel zone is

SHORTED. When the transmitter tamper is in a faulted condition, the

corresponding panel zone is

OPEN.

Note: Supervised transmitters need to report to the module at least once every 12 hours.

If not, the DMP panel indicates that the zone is missing.

LEARN ID? NO YES

TRANSMITTER IDENTIFICATION NUMBER

TRANSMIT NOW

Select

YES to enter Learn ID programming. The keypad displays TRANSMIT NOW. For the

module to learn the transmitter identification number, the transmitter input (reed switch or

contact) must be activated (tripped) and restored. The first activation beeps the program

keypad once. Within four to eight seconds after the first activation the transmitter input must

be tripped and restored a second time. The keypad beeps twice. The keypad displays the

“learned” transmitter identification number (ID). To accept this number, press the

CMD key.

ID: _ _ _ _ _ _ _

Select

NO to manually enter the transmitter identification number. At ID: _ _ _ _ _ _ _, enter

the seven‑digit transmitter number printed under the bar code on the label attached to your

Ademco transmitter. Press

CMD to accept the number.

Note: When programming a 5804BD, you must manually enter the Transmitter ID

Number.

INPUT NO: _

TRANSMITTER INPUT NUMBER

Enter a number (1 to 4) to identify the transmitter input zone. When the transmitter ID is

“learned,” the keypad displays the zone input number. Refer to the Ademco transmitter

installation instructions for zone input information. Default is 

1. Press the CMD key to accept

the number. The display returns to

ZONE NO for programming the next transmitter.

ALREADY ZONE: XX

TRANSMITTER ALREADY LEARNED

This display indicates the transmitter has previously been learned as a zone and continuously

displays until the Back Arrow or

CMD key is pressed. Pressing the Back Arrow key returns

programming to

TRANSMIT NOW to allow a different transmitter to be learned. Pressing the

CMD key returns programming to ZONE NO.

PANEL

ADDRESS

ZONE NUMBERS

XT30/XT50

SERIES

XR150/XR550

SERIES

1

11 to 14

11 to 14

2

21 to 24

21 to 24

3

31 to 34

31 to 34

4

41 to 44

41 to 44

5

51 to 54

51 to 54

6

61 to 64

61 to 64

7

71 to 74

71 to 74

8

81 to 84

81 to 84

738A

ADDRESS

XR150/XR550 SERIES LX‑BUS

PANEL ZONE RANGE

LX‑BUS 1

LX‑BUS 2

LX‑BUS 3

LX‑BUS

4

LX‑BUS 5

1

501

601

701

801

901

2

502

602

702

802

902

3

503

603

703

803

903

...

...

...

...

...

...

16

516

616

716

816

916

17

517

617

717

817

917

18

518

618

718

818

918

...

...

...

...

...

...

32

532

632

732

832

932

Table 1: Keypad Bus Addresses

Table 2: LX‑Bus Addresses