HT82K95EE datasheet(12/45 Pages) HOLTEK

12 / 45 page

HT82K95EE/HT82K95AE

Rev. 1.20

August 28, 2006

WS2

WS1

WS0

Division Ratio

000

1:1

001

1:2

010

1:4

011

1:8

1:16

1:32

1:64

1:128

WDTS (09H) Register

The WDT overflow under normal operation will initialize

²chip reset² and set the status bit ²TO². But in the

HALT mode, the overflow will initialize a

²warm reset²

and only the Program Counter and SP are reset to zero.

To clear the contents of the WDT (including the WDT

prescaler), three methods are employed; external reset

(a low level to RES), software instruction and a

²HALT²

instruction. The software instruction include

²CLR

WDT

² and the other set -²CLR WDT1² and ²CLR

WDT2

². Of these two types of instruction, only one can

be active depending on the ROM code option

-²CLR

WDT times selection option

². If the ²CLR WDT² is se-

lected (i.e. CLRWDT times equal one), any execution of

the

²CLR WDT² instruction will clear the WDT. In the

case wherein

²CLR WDT1² and ²CLR WDT2² are cho-

sen (i.e. CLRWDT times is equal to two), these two in-

structions must be executed to clear the WDT,

otherwise, the WDT may reset the chip as a result of

time-out.

Power Down Operation

- HALT

The HALT mode is initialized by the

²HALT² instruction

and results in the following:

· The system oscillator will be turned off but the WDT

oscillator remains running (if the WDT oscillator is se-

lected).

· The contents of the on-chip RAM and registers remain

unchanged.

· WDT and WDT prescaler will be cleared and re-

counted again (if the WDT clock is from the WDT os-

cillator).

· All of the I/O ports maintain their original status.

· The PDF flag is set and the TO flag is cleared.

The system can leave the HALT mode by means of an

external reset, an interrupt, an external falling edge sig-

nal on I/O ports or a WDT overflow. An external reset

causes a device initialization and the WDT overflow per-

forms a

²warm reset². After the TO and PDF flags are

examined, the cause for chip reset can be determined.

The PDF flag is cleared by a system power-up or exe-

cuting the

²CLR WDT² instruction and is set when exe-

cuting the

²HALT² instruction. The TO flag is set if the

WDT time-out occurs, and causes a wake-up that only

resets the Program Counter and SP, the others remain

in their original status.

The I/O ports wake-up and interrupt methods can be

considered as a continuation of normal execution. Each

bit in the Port A can be independently selected to wake

up the device by option. PB, PC and PD can also be se-

lected to wake up the device by option. Upon awakening

from an I/O port stimulus, the program will resume exe-

cution of the next instruction. If it awakens from an inter-

rupt, two sequence may occur. If the related interrupt is

disabled or the interrupt is enabled but the stack is full,

the program will resume execution at the next instruc-

tion. If the interrupt is enabled and the stack is not full,

the regular interrupt response takes place. If an interrupt

request flag is set to

²1² before entering the HALT mode,

the wake-up function of the related interrupt will be dis-

abled. Once a wake-up event occurs, it takes 1024 tSYS

(system clock period) to resume normal operation. In

other words, a dummy period will be inserted after a

wake-up. If the wake-up results from an interrupt ac-

knowledge signal, the actual interrupt subroutine execu-

tion will be delayed by one or more cycles. If the wake up

results in the next instruction execution, this will be exe-

cuted immediately after the dummy period is completed.

To minimize power consumption, all the I/O pins should

be carefully managed before entering the HALT status.

Reset

There are three ways in which a reset can occur:

· RES reset during normal operation

· RES reset during HALT

· WDT time-out reset during normal operation

The WDT time-out during HALT is different from other

chip reset conditions, since it can perform a

²warm re -

set

² that resets only the Program Counter and SP, leav-

ing the other circuits in their original state. Some regis-

ters remain unchanged during other reset conditions.

Most registers are reset to the

²initial condition² when

the reset conditions are met. By examining the PDF and

TO flags, the program can distinguish between different

²chip resets².

TO PDF

RESET Conditions

RES reset during power-up

RES reset during normal operation

RES wake-up HALT

WDT time-out during normal operation

WDT wake-up HALT

Note:

²u² stands for ²unchanged²

To guarantee that the system oscillator is started and

stabilized, the SST (System Start-up Timer) provides an

HT82K95EE Datasheet(PDF) 12 Page - Holtek Semiconductor Inc

HT82K95EE Datasheet(HTML) 12 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45

Datasheet Download

Link URL