HT82K95EE datasheet(19/45 Pages) HOLTEK

19 / 45 page

HT82K95EE/HT82K95AE

Rev. 1.20

August 28, 2006

· Read operations

The data EEPROM supports three read operations,

namely, current address read, random address read

and sequential read. During read operation execution,

the read/write select bit should be set to

²1².

· Current address read

The internal data word address counter maintains the

last address accessed during the last read or write op-

eration, incremented by one. This address stays valid

between operations as long as the chip power is main-

tained. The address roll over during read from the last

byte of the last memory page to the first byte of the

first page. The address roll over during write from the

last byte of the current page to the first byte of the

same page. Once the device address with the

read/write select bit set to one is clocked in and ac-

knowledged by the EEPROM, the current address

data word is serially clocked out. The microcontroller

should respond a No ACK (High) signal and following

stop condition (refer to Current read timing).

· Random read

A random read requires a dummy byte write sequence

to load in the data word address which is then clocked

in and acknowledged by the EEPROM. The

microcontroller must then generate another start con-

dition. The microcontroller now initiates a current ad-

dress read by sending a device address with the

read/write select bit high. The EEPROM acknowl-

edges the device address and serially clocks out the

data word. The microcontroller should respond with a

²no ACK² signal (high) followed by a stop condition.

(refer to Random read timing).

· Sequential read

Sequential reads are initiated by either a current ad-

dress read or a random address read. After the

microcontroller receives a data word, it responds with an

acknowledgment. As long as the EEPROM receives an

acknowledgment, it will continue to increment the data

word address and serially clock out sequential data

words. When the memory address limit is reached, the

data word address will roll over and the sequential read

continues. The sequential read operation is terminated

when the microcontroller responds with a

²no ACK² sig-

nal (high) followed by a stop condition.

D e v i c e a d d r e s s

D A T A

A C K

S t o p

S t a r t

S D A

N o A C K

Current Read Timing

S e n d W r i t e C o m m a n d

S e n d S t o p C o n d i t i o n

t o I n i t i a t e W r i t e C y c l e

S e n d S t a r t

S e n d C o t r o l l B y t e

w i t h R / W = 0

( A C K = 0 ) ?

N e x t O p e r a t i o n

N o

Y e s

Acknowledge Polling Flow

D e v i c e a d d r e s s

W o r d a d d r e s s

A C K

S t o p

S t a r t

S D A

A C K

N o A C K

A C K

D A T A

D e v i c e a d d r e s s

S t a r t

Random Read Timing

D e v i c e a d d r e s s

D A T A n

S t o p

S t a r t

S D A

A C K

D A T A n + 1

D A T A n + x

N o A C K

Sequential Read Timing

HT82K95EE Datasheet(PDF) 19 Page - Holtek Semiconductor Inc

HT82K95EE Datasheet(HTML) 19 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45

Datasheet Download

Link URL